Publicidad
Idiomas disponibles
Idiomas disponibles
•
Failure to observe the installation, use, operation,
maintenance and repair instructions or performance
of these operations by unqualified personnel;
•
Use on unsuitable and incompatible surfaces.
3 Operation and technical specification
3.1
Operating the machine
The high pressure washer is a professional machine for high pressure
washing with cold water.
It is designed to clean tools, machines,
vehicles, buildings and other surfaces suitable for treatment with a
pressurised water jet. All other uses not mentioned are inappropriate.
3.2
Conditions of use
The high pressure washer has been designed to perform the
functions described in section of this manual only. The machine
must be used in environments conforming to those described in the
paragraph on admissible environmental values.
3.3
Noise
Mod. Comb. engine: Lp dB(A) 106 (uncertainly 1,5) - Lwa dB(A) 110
Mod. ET: Lp dB(A) 93 (uncertainly 1,5). Lw dB(A) 96
Reference Standard EN60335-2-79
3.4
Vibrations
The vibrations produced are minimal and do not represent a source
of danger for the operator.
No particular procedures must be adopted in order to
safeguard the operator from the effects of the vibrations
produced. In the event of abnormal vibrations, the operator
should immediately stop the machine and contact maintenance
personnel.
3.5
Protection class of machines (IP)
Protection class against solid objects (protected
against dust)
Protection class against water (protected against
splashes of water)
3.6
Admissible environmental values
Admissible environmental values
Admissible
operating
temperatures
Variations
in
ambient
temperature
Relative humidity range
Vibrations
The machine is not suitable for operating in environments at risk
from fire or explosion.
The machine may not be used in areas with an
explosive
atmosphere
components or equipment designed to operate in
explosive atmospheres must be indicated with the
(ATEX) mark in accordance with EN 60079-14 (CEI 31-
33)
"Electrical
atmospheres with the presence of gas".
4
Transport and installation
4.1
Lifting and handling
IMPORTANT - Follow the instructions below.
5
4
-10°C ÷ 50°C
(50° F - 113° F)
Max. 1.1°C / Min (Max 2°F /
Min)
75% or less
≤ 0.5 G
Machines
and
relative
constructions
for
explosive
1.
2.
3.
The machine can be delivered from the Manufacturer on a pallet and
packed in a special cardboard box. Before unpacking, the machine
can be transported and handled by means of a lift truck with a
capacity of at least 250 kg.
Straps
Crate
To unpack the machine, remove the straps holding the cardboard
box to the pallet and remove the box. After the machine has been
unpacked, it must be lifted by passing lifting straps through the two
rear hooks. A number of safety instructions relating to transport are
given below.
The lifting and handling operations required for installation
must be performed using adequate lift equipment and by
specialist personnel trained to perform this type of operation,
adopting all the precautions necessary and recommended in
order to prevent damage to people or things.
4.2
Installation
IMPORTANT - Before proceeding with installation
read the following warnings carefully. Failure to
observe the following warnings could cause injury,
death or damage to equipment.
5
Description
Below is a list of the contents of the package delivered to the
customer. If one of the parts listed below is missing, contact the
dealer immediately. To avoid loss during transport, the key is
enclosed in the bag with the technical documents.
•
1 machine
•
1 high pressure hose with:
M24 connectors per 500/15
M22 connectors per 200/41
•
1 handgrip
•
1 wand with nozzle
•
1 use and maintenance manual
6
Operator instructions
6.1
Safety warnings
IMPORTANT - Failure to observe the following safety
rules may cause injury or damage to equipment.
6.1.1
Checks to be performed before starting up the
machine.
Before using the machine, make sure all safety
devices are positioned correctly and are in good
condition.
Pallet
Publicidad
