WERKU WK402020 Instrucciones Originales página 5

ENG ORIGINAL INSTRUCTIONS
either side of the vacuum cleaner and remove the
motor unit (2). For dry-vacuuming, slip the HEPA
filter over the filter basket (7). Attention! The HEPA
filter is suitable for dry-vacuuming only. For wet
vacuuming, slip the supplied foam filter over the
filter basket (8). Attention! The HEPA filter (already
fitted) is not suitable for wet vacuuming. Take care
not to damage the filter. To remove the filter, gently
slide it off the filter basket. Replace the motor unit
and fasten the container latches.
CONNECTING THE HOSE.
The hose can be connected to either the suction
socket or the blower socket. The vacuum socket
is located in the side of the dust container (9).
Line up the notches on the hose end connector
with the slots in the socket (10). Insert the hose
end connector into the socket and rotate until it is
fixed in place (11). The blower socket is located at
the rear of the vacuum cleaner (12). Line up the
notches on the hose end connector with the slots
in the socket (13). Insert the hose end connector
into the socket and rotate until it is fixed in place
(14). Rotate and retract the hose end connector to
disconnect the hose (15).
ASSEMBLING AND FITTING THE EXTENSION TUBES.
Either one or both of the extension tubes can be
used to if additional length is required. To use both
extension tubes together, connect the tubes by
inserting the narrow end of one tube into the flared
end of the other tube (16). Subsequently, slide the
flared end of the extension tube over the nozzle
at the end of the cleaner's handle (17). Slide the
remaining narrow end of the extension tube into
the socket in the brush or the crevice nozzle (18).
To disconnect the tubes, pull the parts gently apart.
FITTING BRUSHES AND NOZZLES.
Slide the end of the vacuum handle or the extension
tube into the socket in the brush or the crevice
nozzle. To disconnect pull the parts gently apart.
CONNECTING TO A POWER TOOL DUST
EXTRACTION OUTLET.
The adapter can be connected to power tools with
a 26, 32, 35 or 45 mm dust extraction outlet. It may
be necessary to cut the power tool adapter to fit
your power tool dust extraction outlet. Slide one
end of the adapter on to the vacuum handle and
the other end of the adapter to your power tool
dust extraction outlet (19). To disconnect pull the
parts gently apart.
DRY VACUUMING - BEFORE SWITCHING ON.
Ensure that the HEPA filter is clean. Using a
dirty HEPA filter for dry vacuuming can lead to
reduced suction and/or permanent damage to the
HEPA filter. To prevent the HEPA filter becoming
unnecessarily
performance and to facilitate easy emptying, we
recommend that a dust bag is always fitted when
dry vacuuming. Ensure that the vacuum cleaner
is correctly assembled. Check that the container
latches are securely fastened.
WET VACUUMING - BEFORE SWITCHING ON.
Attention! For wet vacuuming, use only the
supplied foam filter (8). Remove the dust bag.
Attention! The dust bag must not be used for wet
vacuuming. Ensure that the foam filter is clean
and dry. Wash out if necessary. Using a dirty or
wet foam filter can lead to reduced suction and/
or permanent damage to the filter. Ensure that the
vacuum cleaner is correctly assembled. Check
that the container latches are securely fastened.
SWITCHING ON/OFF.
To switch on, move the switch to position "I" (20).
The vacuum cleaner starts immediately. To switch
off, move the switch to position "O" (21). The
vacuum cleaner stops immediately. For automatic
operation in conjunction with a power tool, to switch
on, plug your power tool into the power take off
socket. Move the switch to position "II" (22). Start
your power tool. The vacuum cleaner starts after
a delay of approximately 5-10 seconds. To switch
off, stop your power tool. The vacuum cleaner
stops. Move the switch to position "O" (21).
CAUTION.
Do not vacuum inflammable or explosive fluids;
for example, petrol, oil, alcohol or solvents. Do not
vacuum hot or burning dust. Do not operate the
vacuum cleaner in rooms where the danger of an
explosion exists. The vacuum cleaner is intended
for vacuuming air and water mixtures. The vacuum
cleaner is not to be used as a water pump. Always
disconnect the vacuum cleaner from the mains
before removing the motor unit, emptying the vacuum
cleaner and fitting or removing the dust bag or filter.
5
English
soiled, to maintain suction