CANGAROO PRESTO Instrucciones De Uso página 14

5.Leave the sterilizer to cool down for about 3 minutes. Turn off the power switch and unplug the
supply cord.
6.Take off the upper lid, the tray and the main body of the sterilizer and pour out the residual water.
Wipe dry the unit. Now the sterilizer is ready for use!
➢WARNING! If you do not clean the sterilizer's base from scale deposition every week, as described
in section "GUIDELINES FOR MAINTANCE AND CLEANING OF THE STERILIZER", the product will
not function normally! We recommend you to use pre-boiled or filtered water in the device in order to
reduce the risk of lime scale deposition.
➢This sterilizer can fit up to 5 standard neck bottles from any brand and 4 wide neck bottles, as well
as other baby feeding items, for e.g. feeding bowls, cups and spoons.
➢The product can be used and for sterilizing accessories, which come into contact with milk – such
as breast pump.
➢Note: Before sterilizing baby bottles and other accessories, first you must clean them with water and
soft detergent!
1.Measure exactly 75ml of water and pour into the reservoir in the base of the unit. (Fig. 1) For your
convenience, there is a 75ml mark on the bottom of the base. Do not add more than 80ml.
2.Put the main body of the sterilizer on its base and place the feeding bottles on the corresponding
stands upside down. (Fig. 2 and 3)
3.After that place the tray on the main body and put inside the pacifiers and other small accessories.
Make sure that all parts, which must be sterilized are completely disassembled, and that you have put
them with their openings facing down in order to avoid their filling with water. (Fig. 4 and 5)
4.Cover with the lid, plug the supply cord to the power outlet and turn on the switch. (Fig. 6)
5.Push the start button. The indicating light will illuminate, showing that the appliance is working (Fig.
7). The sterilization takes from 6 to 8 minutes.
➢ Note: The button for on/ off (0/I) on the rear part of the base, must be switched on.
6.When the sterilization cycle ends, the unit will automatically turn off.
7.Leave the sterilizer to cool down for 3 minutes. Turn off the switch and unplug the supply cord.
Switch off the power button (0/I) on the rear part of the base and unplug the supply cord.
8.Take off the lid and leave the unit until the steam spreads out. After that take out the sterilized
objects. Using the clips, take the small accessories out.
➢Be careful – the sterilized items may still be hot.
➢NOTE: Do not forget to wash your hands thoroughly before taking out the sterilized objects.
9.Take off all of the compartments of the appliance and pour out the residual water. Wipe dry the
sterilizer.
➢Note: If you want to use the sterilizer again, you should wait about 1 hour after the first use.
➢WARNING! Never open the lid during sterilization. If the process is being interrupted, the items will
not be sterilized.
➢Never use the sterilizer without water.
➢Note: If you put more water than the recommended dose of 75 ml, the process of sterilization will
take more time. But if you put less, then the sterilization will not be effective. The length of the
sterilization depends on the quantity of the items, which you have put in the unit.
GUIDELINES FOR MAINTANCE AND CLEANING OF THE STERILIZER
➢ ATTENTION! If you do not clean the base of the sterilizer from scale deposition every week, as
described, the product will not function normally!
➢ WARNING! Not cleaning the product according to the user manual and guidelines below will result in
switching on of the protection and the heating base will be permanently damaged and unusable.
A. CLEANING:
➢Note: Do not use abrasive or aggressive cleaners (e.g. bleach) or sponge with abrasive surface for
cleaning this device.
MANUAL INSTRUCTIONS FOR USE
13