Environmental Protection; Technical Specifications - Metabo WE 2400-180 Manual Original

en ENGLISH
- Unscrew the 4 gear housing screws (a).
CAUTION! Do not remove the gear housing!
- Turn the gear housing to the desired position
without removing it.
- Screw in the 4 gear housing screws (a) in the
available threads! Tightening torque = 3.4 Nm +/-
0.7 Nm.
9. Cleaning
Particles may become deposited inside the power
tool during operation. This impairs the cooling of the
power tool. Conductive build-up can impair the
protective insulation of the power tool and create an
electrical hazard.
The power tool should be cleaned regularly, often
and thoroughly through all front and rear air vents
using a vacuum cleaner or by blowing in dry air.
Prior to this operation, separate the power tool from
the power source and wear protective glasses and
suitable dust mask. Ensure appropriate suction is
available when blowing out vents.
10. Troubleshooting
- Restart protection: The machine does not
start. The restart protection is active. If the mains
plug is inserted with the machine switched on, or if
the current supply is restored following an
interruption, the machine does not start up. Switch
the machine off and on again.
- When switched on, the machine accelerates
to maximum speed very quickly, i.e. automatic
restriction of the starting current does not work
(soft start). An electronic error exists. Other
safety-related electronic functions are no longer
available. Have the machine repaired immediately
(see 12.).
11. Accessories
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating instruc-
tions.
Fit accessories securely. Secure the machine if it is
operated in a bracket. Loss of control can cause
personal injury.
Always use the suitable accessory and the
prescribed guard for the matching guard for
the application. See page 4. (Illustrations are
examples).
Application:
1 = surface grinding
2 = cut-off grinding
3 = drilling of holes
4 = wire brushes
5 = grinding with sanding paper
Accessories:
1.1 = grinding wheel
1.2 = cup wheel (ceramic)
2.1 = cut-off wheel "metal"
2.2 = cut-off wheel "masonry/concrete"
2.3 = diamond cutting disc "masonry/concrete"
18
2.4 = dual-purpose diamond cutting discs
(combined grinding and cutting disc)
3.1 = diamond drill bits
4.1 = wheel brush
4.2 = cup brush
5.1 = flap disc
5.2 = backing pad for sanding sheets
prescribed guard:
Type A = cutting guard
Type B = guard for grinding
Type C = guard for grinding and cutting-off
operations (combination)
Type D = guard for cup wheel
Type F = extraction guard for cutting-off operations
Other accessories:
(see also www.metabo.com)
A Bench cut-off stand
B Adjusting nut (9)
C "Quick"clamping nut
For complete range of accessories, see
www.metabo.com or refer to the main catalogue.
12. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
A defective mains cable must be replaced only with
a special, original mains cable from Metabo
available from the Metabo service.
If the mains connection cable of this tool is
damaged, in order to prevent endangering
personnel and property it must be replaced by the
manufacturer, or the Customer Service of the
manufacturer, or a similarly qualified person.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.

13. Environmental Protection

The sanding dust generated may contain
hazardous materials: do not dispose of with the
household waste, but at a special collection point
for hazardous waste.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Only for EU countries: Never dispose of
power tools in your household waste! In
accordance with European Guideline 2012/
19/EU on used electronic and electric equipment
and its implementation in national legal systems,
used power tools must be collected separately and
handed in for environmentally compatible recycling.

14. Technical Specifications

Explanation of details on page 3. Subject to
changes serving technical progress.
Ø = max. diameter of accessory