Publicidad
Idiomas disponibles
Idiomas disponibles
DESCRIPTION
DESCRIPTION OF THE TEKNA HF GTWIN MONITOR
Hands-free monitor for the Gtwin system with button and coded panels.
k
a
l
m
b
n
f
c
o
g
p
h
d
q
i
k
j
e
r
a.
4.3" TFT colour screen
b.
Communication with hearing aids. Set the hearing aid switch to position T.
c.
Call volume control: maximum, minimum and no volume (night mode).
d.
Function/programming buttons.
e.
Microphone.
f.
Brightness control.
g.
Colour control.
h.
Monitor status LED:
- In call: LED illuminated green.
- In communication: LED blinking green.
- Night mode: LED blinking red.
DESCRIPTION OF THE CONNECTION TERMINALS
CN4 connection terminals:
LINE
LINE
CP
IN
OUT
LINE IN:
Communication bus input to monitor (non-polarised).
LINE OUT:
Communication bus output to additional monitor/
telephone (non-polarised).
CP:
Door bell button input.
FUNCTION BUTTONS
Start/stop communication button.
With the monitor in standby: One short 1-second press activates the monitor in function mode (for 5 seconds).
During a communication process: it activates the talk/listen function, press to talk. (See the TTEKNA HF GTWIN manual, p. 6
and 7, for how to establish communication and enable this function, respectively).
No function.
During a call, communication or auto-spy process: it enables the secondary door release to be activated: one press will
activate the door release for 1 second.
With the monitor in function mode: it enables a call to be made to the guard unit.
With the monitor in function mode: it activates the intercom between 2 devices in the same apartment or in different apartments
(this feature must be pre-programmed, see the TTEKNA HF GTWIN manual, pp. 13-16).
Note: Activation of the
'intercom'
function disables the
With the monitor in standby mode: it enables programming mode to be entered or exited by pressing and holding for 5
seconds, a number of short audible tones will indicate that the monitor is in programming mode and the programming LED
will blink slowly (yellow) or a number of long audible tones will indicate that the monitor has saved and left programming
mode, and the programming LED will turn off.
With the monitor in standby mode: it enables the image from the door panel configured as main to be viewed (if the channel is
busy, a number of short audible tones on the monitor will indicate so); if butto
communication with the door panel to be established.
During a call process: it enables the slave monitors (in the same apartment) to capture the image of the door panel, with the
image on the monitor that was displaying it disappearing.
With the monitor in function mode: it activates the intercommunication between 2 units in the same or different apartments
(function must be programmed in advance), see manual "TTEKNA HF GTWIN" page 13 to 16).
No function.
During call reception and communication processes, it enables the main lock release to be activated.
- In call (night mode): LED illuminated yellow.
- In communication (night mode): LED blinking yellow/
red.
i.
Advanced programming LED:
- In programming: LED blinking yellow.
- Doctor mode: LED blinking green.
- State of the open door on the main panel:
LED illuminated red. (see the TGtwin System Manual,
p. 10)
.
SW1 SW2
-State of the door on the slave door panel:
1 2 3 4 5 6 7 8
1 2
CN3
J2
LED blinking red. ( ee
s
the g
T twin System Manual, p. 10).
CN4
j.
Indicator LED:
- Standby: Off.
CN5
- Call: LED illuminated green.
- Communication: LED illuminated green.
k.
Connector fixings.
s
l.
J2 jumper (end of line) or EL-566 IN-OUT unit connector
(see the TTekna HF Gtwin manual).
m.
SW2 configuration switch.
n.
SW1 configuration switches.
o.
CN3 connector (no function).
p.
CN4 connection terminals.
q.
CN5 connection terminals.
Only by authorised personnel:
r.
Monitor microphone volume control.
s.
Monitor speaker volume control.
CN5 connection terminals:
_
S+ S
PANICO
S+ :
Output (positive) to auxiliary call repeater SAV-GTWIN.
S :
Output (negative) to auxiliary call repeater SAV-GTWIN.
PANICO:
Input for panic button. (Sends a panic signal to guard unit).
'call to guard unit'
function.
n
is pressed, it enables audio and video
2
OPERATION
- Call reception: During call reception, the image will appear on the master monitor and status LED
master and slave monitors will illuminate (green). If the call is not answered within 60 seconds, the indicator LED and status LED
on the master and slave monitor(s) will turn off. LED
- To establish communication, press button
illuminate and LED on the door panel will turn off.
away from the monitor to ensure maximum audio quality during communication with the door panel.
switch to the T position, making conversation possible (inductive loop).
- Guaranteed communication time is 90 seconds (configurable); after 90 seconds of guaranteed communication time, the channel
will become free.
- To end communication, press button
and the channel will become free.
- To open the main or secondary door, press the corresponding door release button
processes: one press will activate the lock release for 1 second (configurable main door) and, with the opening of the main door,
LED
will also illuminate for 1 second.
INSTALLATION
Avoid dusty or smoky environments or locations near sources of heat. The monitor can be fixed to an electrical embedding box or
Important:
directly to the wall.
For further information, see the TTekna HF Gtwin manual (code 50120254).
Location
1.60m
Remember to remove the protective covering from the front of the monitor once installation is complete.
ADVANCED PROGRAMMING OF THE TEKNA HF GTWIN MONITOR
Advanced programming enables the monitor's default settings to be changed:
With the monitor in standby: Press button
short audible tones will confirm this and the monitor's programming LED will blink (yellow) slowly,
indicating that button
Then adjust the settings as required:
- Changing the door panel ringtone melody:
The monitor enables selection of the ringtone (5 different tones).
Select the ringtone melody: Press button
- Changing the ringtone melody from the apartment front door:
The monitor enables selection of the ringtone from the apartment front door (5 different tones).
Select the ringtone melody from the apartment front door: Press button
'carousel mode.'
- Activating/deactivating the doctor mode function: Doctor mode not activated (default setting).
The 'doctor mode' function enables the main lock release to be activated automatically 3 seconds after making a call
from the door panel without having to establish communication or press door release button
15 seconds and the channel becomes free. (Only the master monitor should be configured with 'doctor mode').
To activate doctor mode: Press button
pressed again, an audible tone will indicate that the function will change its status to deactivated and so on. The
monitor's programming LED will blink (green) slowly when the monitor exits programming mode and is in standby.
-
Exiting programming mode:
'programming mode,'
To exit
this and the programming LED will turn off, indicating that button
Note: When exiting programming mode, if 'doctor mode' has been activated, the monitor's programming LED will
blink slowly (green), see p. 2.
EN
on the door panel will turn off and the channel will become free.
on the monitor, status LED
will blink (green), LED
Communication with hearing aids
: Make sure that the hearing aid is 1 -
, and the monitor's indicator LED and status LED
and door panel LED
/
Surface
Embedding box
4 30
x
for more than 5 seconds to access
can be released.
until the desired melody is heard 'carousel mode.'
until the desired melody is heard
once, an audible tone will indicate that the function is activated; if it is
press button
for more than 5 seconds, 1 short and 2 long audible tones will confirm
can be released.
3
and the indicator LED on the
.
on the door panel will then
0 15
cm
Remember:
Set the hearing aid
will turn off
during the call or communication
Screws supplied with the
embedding box.
'programming mode,'
3
. The call ends after
EN
Publicidad
