Descargar Imprimir esta página

Auxiliary Handle (See Figure A); Dust Extraction/Dust Container - Bosch AdvancedImpact 900 Manual Original

Ocultar thumbs Ver también para AdvancedImpact 900:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 27
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Auxiliary Handle (see figure A)
Do not operate your power tool without the auxiliary
u
handle (9).
Before any work, make sure that the wing bolt (18)/
u
(21) is tightened. Loss of control can cause personal in-
jury.
You can adjust the auxiliary handle (9) to any of four posi-
tions in order to achieve a safe work posture that minimises
fatigue.
Turn the wing bolt (21)/(18) anticlockwise and guide the
auxiliary handle (9) in the required position over the drill
chuck onto the spindle collar of the power tool.
Turn the wing bolt (21)/(18) clockwise to retighten it.
Setting the Drilling Depth (see figure B)
You can use the depth stop (23) to set the required drilling
depth X.
Press the button for depth stop adjustment (22) and insert
the depth stop into the auxiliary handle (9).
The fluting on the depth stop (23) must face downwards.
Pull the depth stop (23) far enough out that the distance
between the drill bit tip and the edge of the depth stop (23)
corresponds to the required drilling depth X.
Drill Assistant (accessory)
Applying the Drill Assistant (see figures C–D)
The Drill Assistant  (10) can be used with and without the
dust collection device (13). Use of the dust collection
device (13) is limited to drill bits with a diameter of 12 mm
and a length of 120 mm.
Attach the dust collection device (13) to the adapter (26).
Press the unlocking button (8) to release the Drill Assistant 
(10) from its parked position.
Guide the Drill Assistant  (10) over the drill chuck onto the
spindle collar of the power tool.
Lock it by turning the wing bolt (18) clockwise.
Setting the Drilling Depth (see figures E–F)
Attach the drill bit (see section "Changing the Tool").
You can use the setting ring (17) to set the required drilling
depth X.
Unlock the setting ring (17) by turning it to the left
Place the dust container (11) or the adapter (26) flush
against the wall or workpiece. Move the tip of the drill bit to
the wall or workpiece.
Slide the setting ring (17) backwards until the distance
matches the required drilling depth X or place a wall plug on
the rail and slide the setting ring (17) backwards to the wall
Bosch Power Tools
plug. Lock the setting ring (17) by turning it to the right .
Take the wall plug out of the rail again. The drilling depth now
matches the set length X on the rail.
Note: It is important to have the exact drilling depth when
using wall plugs. If the drilled hole is too deep, the wall plug
will slip too far into the wall or workpiece. If the hole is too
small, the wall plug will stick out.
Emptying the dust container (see figure G)
The dust container (11) is enough for drilling about 25 holes
in masonry at a drilling depth of 30 mm with a drill bit dia-
meter of 6 mm.
To remove the dust container (11), press the side-mounted
unlocking buttons (12) and pull the dust container off down-
wards.
Empty the dust container (11) and reinsert it (until it can be
heard to engage).
Removing the Drill Assistant
Press and hold the clip (16) of the dust collection
device (13) and pull the dust collection device (13) off to-
wards the front.
Turn the wing bolt (18) anticlockwise until the auxiliary
handle (9) can be moved and pull the auxiliary handle (9) off
the power tool.
Unlock the setting ring (17) by turning it to the left
Hold the auxiliary handle (9) in place and slide the rail to-
wards the auxiliary handle until it can be heard to engage.

Dust Extraction/Dust Container

The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Use the dust box only when working on concrete and
u
stone. Wood chips and plastic chips can easily lead to
clogging.
.
Warning: Danger of fire! Do not work on any metallic
u
materials with the dust container mounted. Hot metal
chips can ignite parts of the dust container.
English | 17
.
1 609 92A 867 | (26.07.2022)

Publicidad

loading

Este manual también es adecuado para:

Advancedimpact 9000