Publicidad
Idiomas disponibles
Idiomas disponibles
Fig. Step
1 . Turn the extension pole
so that the L-shaped bolt
upwards .
2 . Remove the L-shaped bolt
C
washer
from the extension pole
[
16 ]
3 . Place the base
on the extension pole
[
15 ]
4 . Fasten the washer
bolt
.
[
17 ]
1 . Turn the assembled parts from the previous
assembly step upside down . Place the
base
on the floor .
14 ]
[
2 . Loosen the lock screw
D
extension pole
3 . Place the motor unit's
the extension pole
the back side . Tighten the lock screw
Pull off the protective sleeve from the motor
E
shaft
. Discard the protective sleeve .
4 ]
[
Remove the 4 lock screws
F
unit
.
10 ]
[
1 . Align the rear grille handle
and to the rear . Attach the rear grille
G
to the motor unit
2 . Tighten with the 4 lock screws
Point the groove on the motor shaft
H
upwards .
1 . Loosen the lock screw
blade
(the lock screw is pre-assembled
1 ]
[
on the blade's screw thread) .
I
Place the blade on the motor shaft
blade's rear with the lock screw is facing
the motor unit
2 . Tighten the lock screw
upside down
13 ]
[
is directed
[
17 ]
and the
[
17 ]
13 ]
[
and the base weight
14 ]
[
.
13 ]
[
and the L-shaped
[
16 ]
from the
11 ]
[
.
13 ]
[
upper pole on
10 ]
[
. Align the hole on
13 ]
[
from the motor
[
18 ]
upwards
[
3 ]
.
[
10 ]
.
18 ]
[
4 ]
[
from the
19 ]
[
4 ]
[
) .
10 ]
[
.
[
19 ]
Fig. Step
1 . Open the 5 grille clips
grille
2 . Remove the lock nut and the lock
screw
J
.
3 . Hang the hanger
on the rear grille
NOTE: The 5 grille clips
the frame of the rear grille
Insert the lock screw
K
nut
. Close the 5 grille clips
[
21 ]
frame .
˜ Height adjustment
Loosen the height adjustment knob
(positioned on the extension pole
.
[
11 ]
counter-clockwise direction .
Adjust the length of the extension pole
Tighten the height adjustment knob
clockwise direction .
˜ Tilt adjustment
Loosen the knob
2 ]
[
Adjust the tilt angle manually .
Tighten the knob
Do not perform the tilt adjustment when the
product is in operation .
NOTE: The screw and the nut
for guiding the tilt adjustment . Neither remove the
screw not the nut when adjusting the tilt angle .
˜ Operation
(the
Place the product on a flat, stable ground .
Connect the power plug
socket-outlet .
on the front
[
20 ]
.
22 ]
[
from the front grille
21 ]
[
of the front grille
[
23 ]
.
2 ]
[
[
20 ]
[
2 ]
. Fasten the lock
[
21 ]
20 ]
[
13 ]
[
.
[
9 ]
again .
9 ]
[
are intended
[
8 ]
to a suitable
7 ]
[
.
[
22 ]
[
22 ]
must fit over
.
at the grille
12 ]
[
) in a
.
13 ]
[
in a
[
12 ]
GB/MT
19
Publicidad
