US Blaster USB 71 00 Instruction Manual página 4

HINT: You can record sample with the PITCH (41) control in any position. Whatever that position is will become normal sound. If you start to record a sample with the
PITCH (41) control set at minimum (this now becomes your normal pitch), by increasing the pitch to maximum, the pitch effect will double in speed. Recording at maxi-
mum and lowering to minimum will do exactly the opposite.
3. Tapping the START/STOP (45) button begins the sampling process (the SAMPLER INDICATOR will illuminate RED). Tapping the SAMP; ER INDICATOR will turn off). If you
do not tap the START/STOP (45) button a second time, the sampling process will stop automatically after 2,4 or 12 seconds depending on which MEMORY BANK (44) was
selected.
SAMPLE PLAYBACK:
1. Put the MODE SELECETOR (43) switch into the SINGLE or REPEAT position.
2. Select the memory bank you wish to play by pressing the proper MEMORY BANK (44) button.
3. Tapping the STAR/STOP (45) button with the MODE SELECTOR (43) switch in the SINGLE position will cause the sampler to playback one time (the SAMPLER INDICTOR
will illuminate GREEN). Every push of the START/STOP (45) button will restart the sample from the beginning. Rapid pressing of the START/STOP button will cause a stut-
tering effect. Once the sample has started start playback and the START/STOP (45) button is not pushed a second time, the sample will play to the end and then stop (the
SAMPLER INDICATOR will turn off)
4. Tapping the START/STOP (45) button with the MODE SELECTOR (43) switch in the REPEAT position will cause the sample to continuously play over and over (the SAM-
PLER INDICATOR will illuminate GREEN). The START/STOP (45) button will act as an on/off switch. The first push will start the sample, the second push will stop it The
SAMPLER LEVEL (40) controls the level of the sample
ROBO PLAY:
With the ROBO PLAY (42) button in the OFF POSITION ( the ROBO PLAY INDICAOR will be OFF) and the MODE Selector (43) Switch in either the SINGLE or REPEAT mode.
Pressing the START STOP (45) button will cause the sample to play along with the selected source.
When the ROBO PLAY (42) button is in the ON position (the ROBO PLAY INDICAOR illuminator RED), starting the sampler mutes the selected source. When the sample
ends the source automatically turns back on.
BATTERY BACKUP: The USB 7100 is equipped with battery backup to retain samples. To activate this feature . a 9 volt battery (not included) needs to be connected to the
BATTERY HOLDER (54) located on the rear panel. this will enable you to store samples in memory, and when the unit is unplugged, the battery backup will retain the samp-
les for future use. If the unit is unplugged with no battery attached, all the sample will be lost
LOW BATTERY INDICATOR: A low battery indicator is included with the USB 7100. When changing the battery, make sure the unit is plugged in and the power is ON. Failure
to adhere to this will result in lost memory. The low battery indicator is ON when selected memory bank LED blinks. The LED will also blink if no battery is connected to the
unit.
Specifications
INPUTS:
DJ Mic
Phono
Line
Aux
OUTPUTS:
Main/Aux
Max
Rec
MIC 1&MIC 2:
DJ Mic
Bass
High
1.5mV 2Kohm balanced
3mV 47Kohm
150 mV 27Kohm
150 mV 27Kohm
0 dB 1V 400ohm
20V Peak to Peak
225Mv 5Kohm
1.5mV 2Kohm balanced
±12dB
±12dB
GENERAL:
Frequency Response
Distortion
S/N Ratio
Talkover Attenuation
Headphone Impedance
Powersource
Dimensions
Weight
Copyright U.S. Blaster Europe BV © - Delft - Netherlands
20Hz-20KHz +/-2dB
0.02%
batter than 80dB
16dB
16ohm
115/230V 50/60Hz 10W
19"wx4"hx9"d
4,6 kg
ENG
5