WERKU WK500600 Instrucciones Originales página 5

ENG
manuals and follow all warnings
sprayer Refer to the instructions in the sprayer's
►
owner's manual Attach a grounded hose to
►
the material inlet on the airless gun
wrenches (one on the airless gun and one on
the hose), tighten securely (4)
tip guard off the airless gun, start the sprayer
Flush and prepare the spray system according
►
to the sprayer's owner's manual
spray system to make sure that all fittings are
secure and that there are no leaks
the pressure relief procedure described in the
sprayer's owner's manual
similar object, insert the tip seal and seal into
the back of the tip guard (5)
adjustment Insert the tip into the slot on the
►
tip guard (6) Thread the tip guard onto the
►
airless gun Position the tip guard in the desired
►
spraying position, then tighten securely.
OPERATION.
Make sure the arrow on the tip handle is
►
pointing in the forward direction for spraying
Start the sprayer
► ►
in the sprayer's owner's manual
fluid pressure on the sprayer until the spray is
completely atomized
pressure necessary to get the desired results
The spray tip determines the size of spray
►
pattern and coverage
needed, use a larger tip instead of increasing fluid
pressure.
CLEAR CLOGGED TIP.
Rotate the tip 180º so that the arrow on the tip
►
handle is pointing opposite the spray direction
(7) Trigger the airless gun once so that the
►
pressure can blow the clog out
trigger more than once at time with the tip in the
reverse position Continue this procedure until
►
the tip is clear of the clog.
CHANGING TIP.
Tips can be removed and replaced easily
►
without disassembling the airless gun
attempt to change or clean the tip or tip
guard without first performing the pressure
relief procedure Perform the pressure relief
►
procedure described in the sprayer's owner's
Set up the
►
Using two
►
With the tip and
►
Inspect the
►
Perform
►
Using a pen or
►
Press in for final
►
Refer to the instructions
Adjust the
►
Always spray at the lowest
►
When more coverage is
►
Never pull the
►
Never
►
manual Remove the tip from the slot on the tip
►
guard Insert the new tip into the slot on the tip
►
guard The arrow on the tip handle should be
►
pointing in the forward direction for spraying.
REMOVING SEAL AND TIP SEAL.
Remove the tip and tip guard from the airless
►
gun Remove the seal and tip seal from the
►
back of the tip guard (8).
IDENTIFYING TIP SIZES.
To identify tip sizes, use the following formula
►
A 517 tip size will be used in this example
►
The first digit multiplied by two represents the
►
size of the spray pattern when spraying 12" (30
cm) away from the work surface: 5 x 2 = 10"
(25 cm) spray pattern
represent the diameter of the orifice on the tip:
17 = 0.017" (0.43 mm) orifice
will adversely affect the spray pattern and result
in reduced production, poor finish, and wasted
material ►Replace worn tips immediately.
CLEANUP.
Maintaining a clean airless gun is important to
►
ensure trouble-free operation
gun after each use and store in a dry location
Do not leave the airless gun or any of its parts
►
in water or solvents.
CLEANUP INSTRUCTIONS FOR USE WITH
FLAMMABLE SOLVENTS.
Always flush airless gun preferably outside
►
and at least one hose length from spray pump
If collecting flushed solvents in a 4 liter
►
metal container, place it into an empty 20 liter
container, then flush solvents
free of flammable vapors
instructions
gun should be cleaned thoroughly after daily
use Failure to do so permits material to cake,
►
seriously affecting the performance of the unit
Always spray at minimum pressure with the
►
tip and tip guard removed when using mineral
spirits or any other solvent to clean the sprayer,
hose or airless gun
may result in a fire or explosion in the presence
of flammable vapors
against a metal container while flushing.
5
English
The second two digits
►
Worn spray tips
►
Flush the airless
►
Area must be
►
Follow all cleanup
►
The sprayer, hose and airless
►
Static electricity buildup
►
Hold the airless gun firmly
►