Proper Use - Collomix Xo 1 R Manual De Servicio Original

EN
Read and observe the opera琀椀ng
instruc琀椀ons for the machine before you
start it up!
Always wear protec琀椀ve goggles and ear
protec琀椀on while working.
It is advisable to wear a dust mask
whenever working with materials which
generate large amounts of dust.
Always wear protec琀椀ve gloves while
working.

Proper use

The machine is designed for mixing liquid and powder-
based building products such as paints, mortar,
adhesives, plaster and similar substances. Use the right
mixing tool for the consistency of the material and the
quan琀椀ty to be mixed.
Please refer to the informa琀椀on in the technical data
when choosing the size of mixing tool (diameter/
mixing ac琀椀on). If the wrong mixing ac琀椀on or mixing tool
diameter is selected, this may cause the machine/gear
unit to become overloaded and lead to damage as a
result. Please remember that a mixing tool with a mixing
ac琀椀on from the top down puts a greater strain on the
electrical tool than one with the reverse mixing ac琀椀on.
Given the high torque levels generated by the machine, it
must not be used as a power drill.
The machine must not be used for the prepara琀椀on of
foodstu昀昀s.
The machine is not suitable for mixing materials
containing graphite dust, brine or slurry. Mixing of
these materials or substances may damage the machine
beyond repair.
Assembly
► Always pull the power plug out of the socket outlet
before carrying out any work on the machine.
Fi琀�ng the mixing tool mount:
Take the HEXAFIX coupling or size M14 adapter supplied
with the packaging and screw it to the male thread of the
mixing sha昀琀.
Fi琀�ng the mixing tool / tool change-over:
HEXAFIX (Fig. A)
Insert the mixing tool with the HEXAFIX mount in
the coupling un琀椀l it locks. To release or change the
mixing tools, simply pull back the handle-collar
on the coupling and this releases the mixing tool.
(Fig. C)
M14 (Fig. B)
Screw the mixing tool with a size M14 male thread into
the M14 adapter on the mixing sha昀琀. The mixing tool
琀椀ghtens itself during opera琀椀on.
To release the mixing tool you will need one SW 22 and
one SW 24 open-ended wrench. Place the one open-
ended wrench on the adapter and the other on the
hexagonal holding 昀椀xture and turn them both in opposite
direc琀椀ons to one another un琀椀l the mixing tool is released.
Opera琀椀on
► Check that the power supply shown on the rating
plate is the same as the mains power supply.
Always hold the machine with both hands.
Press the star琀椀ng lockout bu琀琀on (1).
1.
2.
To stop working, release the ON/OFF switch.
Machines with 2-speed gear
units (Xo4R/Xo6) have two
maximum speeds available (First
gear: Slow / Second gear: Fast).
To change from one gear to the
other, turn the gear selec琀椀on
lever through 180°.
Only ever actuate it when the
machine is at a stands琀椀ll.
L
WARNING
Tips for safe working:
Always reduce the speed when submerging the mixing
tool in the mixing material or li昀琀ing it out. Once the
mixing tool is fully submerged, increase the speed again
to ensure that the motor is adequately cooled.
During mixing you should guide the machine around
the mixing container. Con琀椀nue mixing un琀椀l all of the
mixing material is completely mixed. Please follow the
processing instruc琀椀ons of the manufacturer of the
material.
You work be琀琀er and safer when the mixing tool used is
clean, free of material residues and in perfect condi琀椀on.
Press the ON/OFF switch (2).
The more pressure you apply to
the ON/OFF switch,
the faster the machine will run.
The ON/OFF switch cannot be
locked!
Always work with the ON/OFF
switch fully pressed.