Makita XRU16 Manual De Instrucciones página 4

Cortador inalámbrico de pasto
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

7.
Under abusive conditions, liquid may be
ejected from the battery; avoid contact. If con-
tact accidentally occurs, flush with water. If
liquid contacts eyes, seek medical help. Liquid
ejected from the battery may cause irritation or
burns.
Do not use a battery pack or machine that is
8.
damaged or modified. Damaged or modified
batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
9.
Do not expose a battery pack or machine to
fire or excessive temperature. Exposure to fire
or temperature above 130°C (265°F) may cause
explosion.
10. Follow all charging instructions and do not
charge the battery pack or machine outside of
the temperature range specified in the instruc-
tions. Charging improperly or at temperatures
outside of the specified range may damage the
battery and increase the risk of fire.
11.
Have servicing performed by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the product is
maintained.
12. Do not modify or attempt to repair the machine
or the battery pack except as indicated in the
instructions for use and care.
13. Do not dispose of the battery(ies) in a fire.
The cell may explode. Check with local codes for
possible special disposal instructions.
14. Do not open or mutilate the battery(ies).
Released electrolyte is corrosive and may cause
damage to the eyes or skin. It may be toxic if
swallowed.
15. Do not charge battery in rain, or in wet
locations.
16. Make sure there are no electrical cables, water
pipes, gas pipes etc. that could cause a hazard
if damaged by use of the tool.
Starting up the tool
Make sure that there are no children or other
1.
people within a working range of 15 meters
(50 ft), also pay attention to any animals in the
working vicinity. Otherwise stop using the tool.
Before use always check that the tool is safe
2.
for operation. Check the security of the cutting
tool and the guard and the switch trigger/lever
for easy and proper action. Check for clean
and dry handles and test the on/off function of
the switch.
3.
Check damaged parts before further use of
the tool. A guard or other part that is damaged
should be carefully checked to determine
that it will operate properly and perform its
intended function. Check for alignment of
moving parts, binding of moving parts, break-
age of parts, mounting, and any other condi-
tion that may affect its operation. A guard or
other part that is damaged should be properly
repaired or replaced by our authorized ser-
vice center unless indicated elsewhere in this
manual.
Switch on the motor only when hands and feet
4.
are away from the cutting tool.
5.
Before starting make sure that the cutting
tool has no contact with hard objects such as
branches, stones etc. as the cutting tool will
revolve when starting.
Remove any adjusting key, wrench or blade
6.
cover before turning the power tool on. An
accessory left attached to a rotating part of the
power tool may result in personal injury.
Make sure there are no electrical cables, water
7.
pipes, gas pipes etc. that could cause a hazard
if damaged by use of the tool.
Do not use a cutting tool which is not recom-
8.
mended by Makita.
9.
Do not operate the tool in bad weather or if
there is a risk of lightning.
Method of operation
1.
Only use the tool in good light and visibility.
During the winter season beware of slippery
or wet areas, ice and snow (risk of slipping).
Always ensure a safe footing.
2.
Take care against injury to feet and hands from
the cutting tool.
3.
Never cut above waist height.
4.
Never stand on a ladder and run the tool.
Never climb up into trees to perform cutting
5.
operation with the tool.
6.
Never work on unstable surfaces.
7.
Remove sand, stones, nails etc. found within
the working range. Foreign particles may dam-
age the cutting tool.
8.
Should the cutting tool hit stones or other hard
objects, immediately switch off the motor and
inspect the cutting tool.
9.
Before commencing cutting, the cutting tool
must reach full working speed.
10. During operation always hold the tool with
both hands. Never hold the tool with one hand
during use. Always ensure a safe footing.
The cutting tool has to be equipped with the
11.
guard. Never run the tool with damaged guards
or without guards in place!
12. All protective equipment such as guards
supplied with the tool must be used during
operation.
13. Except in case of emergency, never drop
or cast the tool to the ground or this may
severely damage the tool.
4 ENGLISH

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Xru17

Tabla de contenido