Descargar Imprimir esta página

FONESTAR ASH-1200 Manual De Usuario página 6

Ocultar thumbs Ver también para ASH-1200:

Publicidad

Idiomas disponibles

Idiomas disponibles

EN
14.- REPEAT (RPT): audio track repeat modes: repeat 1 and repeat all.
15.- PROG: allows the creation of a playlist. For more information, please refer to the INSTRUCTIONS FOR
USE section.
16.- VOL-/VOL+: buttons to decrease/increase the volume of the module.
17.- USB/SD/DISC: Direct selection buttons for USB/SD/CD operation mode.
18.- PWR: power on/standby of the CD module.
MSHTM-1200L + MSHRM-1200L
MSHTM-1200L
1.- AUDIO: Audio signal indicator light. This indicator lights up whenever it transmits audio signal.
2.- CH-/CH+: transmit-receive channel selection buttons.
3.- RF: audio signal indicator light. This indicator lights up whenever an audio signal is detected.
CONNECTION - INSTRUCTIONS FOR USE
SYNCHRONISE MSHTM-1200M/MSHTM-1200P MICROPHONES WITH UHF RECEIVER MSHRM-1200
-
Select a free channel on the receiver using the CH-/CH+ buttons.
-
Press the SYNC button on the receiver.
-
Move the microphone and receiver IR sensors close together and facing each other so that they can be
synchronised to the same channel. The IR sensor on the receiver will flash during the process and turn
off when finished.
+
WIRELESS SPEAKER CONNECTION ASH-1200 (MSHTM-1200L + MSHRM-1200L)
Install the MSHTM-1200L module in the main loudspeaker and the MSHRM-1200L module in the
-
secondary loudspeaker.
-
The BROADCAST selector on the main speaker should be set to TX and on the secondary speaker to RX.
-
Turn on both loudspeakers from the POWER switch and their modules via the VOLUME control below
the BROADCAST selector. And on all loudspeakers set the LINK SET selector to the MASTER position.
-
As soon as the connection of both loudspeakers is established and the audio is being transmitted-
received, the indicator lights on both modules will light up indicating the correct functioning of the
connection.
WIRED CONNECTION OF ASH-1200 LOUDSPEAKERS
You can connect the loudspeakers using the INPUT and OUTPUT using male XLR cables.
-
Connect all sound sources to the MASTER speaker and set the LINK SET selector to the MASTER
position.
-
On the subwoofer, set the LINK SET selector to the SLAVE position.
-
Connect the OUTPUT output of the main speaker to the INPUT input of the secondary speaker.
Configure the main speaker (sound source)
-
You can control the volume individually with the MASTER and SLAVE volume controls.
Configure el altavoz principal (fuente de sonido)
Configurez le haut-parleur principal (source de son)
WIRED CONNECTION TO A PASSIVE LOUDSPEAKER
Configure a coluna principal (fonte de som)
A 6.3 mm male jack cable enables you to connect a passive loudspeaker to the ASH-1200 loudspeaker
using the EXT SPK output.
PLAYLIST PROGRAMMING ON CDM-1200
1
2
RED/ROJO/
ROUGE/VERMELHO
AUDIO
RF
ON/ENCENDIDO/ALLUMÉ/LIGADO
OFF/APAGADO/ÉTEINT/DESLIGADO
MSHTM-1200L
SELECT a free channel
SELECCIONE un canal libre
SELECTIONNEZ un canal libre
SELECCIONE um canal livre
MSHRM-1200L
5
6
+
MSHRM-1200L
Configure the secondary speaker (sound receiver)
Configure el altavoz secundario (receptor de sonido)
Configurez le haut-parleur secondaire (récepteur de son)
Configure a coluna secundária (recetor de som)
- 6 -
3
2
SELECT the same channel
SELECCIONE el mismo canal
SELECTIONNEZ le même canal
SELECCIONE o mesmo canal

Publicidad

loading