•
The base should always be used in the lowest position as soon as the child is old enough to
sit, kneel or to pull itself up.
•
Accessories which are not approved by the manufacturer shall not be used.
•
Do not leave anything in the playpen or place the playpen close to another product, which
could provide a foothold or present a danger of suffocation or strangulation, e.g. strings,
blind/curtain cords.
•
All assembly fittings should always be tightened properly.
•
Do not use the playpen if any part is broken, torn or missing and use only spare parts
approved by the manufacturer.
•
If you leave the child in the playpen unattended, always check, if the side entrance is fastened
with a zip.
1
Cot frame with four legs
2
Metal mattress brackets x 4
1. Assembly of the cot with the mattress in the top position (figure I)
Remove the cot from the bag. Pull on the shorter sides of the frame to unfold the cot (figure A). You'll hear a distinctive "click" if the
assembly has been carried out correctly. Place the plastic legs into the legs of the cot (figure B). Make sure the leg you've chosen has a
buckle matching the buckle of the cot cover. Unfold the cot legs. You'll hear a distinctive "click" if the assembly has been carried out
correctly. (C) Next, clip the cover buckles with the leg buckles (figure D). Unfold the mattress by pulling on one side (figu re E); place the
mattress on a clean surface so that the pockets for the metal brackets are visible. Slide the ends of the metal brackets marked with openings
into the pockets. Connect them, and secure the connection point using hook-and-loop closures (figure F). Place the mattress in the cot
(figure G). There are six hook-and-loop closures on the bottom of the mattress. Thread them through the base of the cot and connect to
the hook-and-loop closures underneath. Make sure that the zipper is secured with the buckle (figure H).
2. Assembly of the cot with the mattress in the lower position (figure L)
Remove the cot from the bag. Pull on the shorter sides of the frame to unfold the cot (figure A). You'll hear a distinctive "click" if the
assembly has been carried out correctly. Place the plastic legs into the legs of the cot (figure B). Unfold the cot legs. You'll hear a distinctive
"click" if the assembly has been carried out correctly. (C) To unroll the material to the lower position, open the buckle (figure H) and open
the zipper around the perimeter of the cot. Fasten both buckles on the straps to the leg buckles in each corner (figure J). Unfold the mattress
by pulling on one side (figure E); place the mattress on a clean surface so that the pockets for the metal brackets are visible. Slide the ends
of the metal brackets marked with openings into the pockets. Connect them, and secure the connection point using hook-and-loop closures
(figure F). Place the mattress in the cot (figure G). There are six hook-and-loop closures on the bottom of the mattress. Thread them through
the base of the cot and connect to the hook-and-loop closures underneath. The cot has side access – open the zipper to open it (figure K).
3. Folding the cot
Open the hook-and-loop closures connecting the mattress to the base of the cot, and remove the mattress. Open the buckles connecting
the material with the legs (figure M). Place the cot upside down. Straighten the cot base material. Slide the lever on the cot leg down, and
fold the leg towards the inside of the cot. Repeat with the remaining legs. There are buttons in the middle part of the longer sides of the
frame. Press them while simultaneously folding the frame of the cot in half (figure O).
4. Cleaning
Cot fabric – remove the fabric from the cot by opening the zippers underneath the cot frame. You can hand wash it in warm water using
mild detergent. Mattress cover – remove the mattress cover by opening the zipper. You can hand wash it in warm water using mild
detergent. Never clean using abrasive ammonia-based cleaners, whitening agents or spirits. The cot must be completely dry before use and
storage. Frame and legs – clean the metal frame using a soft, clean, damp cloth and mild soap.
Hand wash in warm water using mild detergent.
Do not dry clean
Do not iron
5. Warranty
1.
All Kinderkraft products are covered by a 24-month warranty. The warranty period starts from the date the product is handed over
to the Buyer.
3
Plastic legs x4
4
Mattress
Do not tumble dry
Do not bleach
14