Cable Specifications; Circuit Diagram - BOMANN CL 6044 QC CB Manual De Instrucciones

Tightening Torque for Protective Caps and Flange Connections
Cooling pipe Tightening torque (N × m)
1 / 4" 6
3 / 8" 9,52
1 / 2" 12
5 / 8" 15,88
Model
Power cable
Connecting cable
Voltage transformer
Model
Power cable
Connecting cable
At 220 V 7 K, 9 K, 12 K, 15 K, 16 K, 18 K, 22 K, 24 K, 30 K, the backup value for the air conditioning interior unit is: 50 T, 3.15 A
At 110 V 7 K, 9 K, 12 K, the backup value for the air conditioning interior unit is: 50 T, 3.15 A
125 V 7 K, 9 K, 12 K the backup value for the air conditioning exterior unit is: 61 T, 15 A
250 V 18 K, 22 K, 24 K the backup value for the air conditioning exterior unit is: 65 T, 25 A!

Circuit Diagram

The circuit diagram may vary for different models. Please observe the
circuit diagrams on the interior and exterior units.
For the interior unit, you will find the circuit diagram (7) under the front
panel (1).
For the exterior unit, you will find the circuit diagram stuck to the reverse
side of the connector cover (15).
84
CL6044CB_IM
Corresponding load use:
20 cm wrench)
15 - 20 Tight / hand-tight
31 - 35 Tight
35 - 45 Tight
75 - 80 Tight

Cable Specifications

Installation Instructions – Information for the Installer
Cooling agent (Btu / h)
N
L
E
N
L
1
2
3
Installation Instructions – Installation Information
Cooling agent (Btu / h)
1.0 mm² (1.5 mm²)
N
AWG18 (AWG16)
1.0 mm² (1.5 mm²)
L
AWG18 (AWG16)
1.0 mm² (1.5 mm²)
E
AWG18 (AWG16)
N 1.0 mm² (1.5 mm²)
L 1.0 mm² (1.5 mm²)
1 1.0 mm² (1.5 mm²)
Service-connecting nut
Protective caps
9k 12k
1.0 mm² 1.0 mm² (1.5 mm²)
AWG18 AWG18 (AWG16)
1.0 mm² 1.0 mm² (1.5 mm²)
AWG18 AWG18 (AWG16)
1.0 mm² 1.0 mm² (1.5 mm²)
AWG18 AWG18 (AWG16)
1.0 mm² 1.0 mm² (1.5 mm²)
1.0 mm² 1.0 mm² (1.5 mm²)
1.0 mm² 1.0 mm² (1.5 mm²)
0.75 mm² 0.75 mm²
0.75 mm² 0.75 mm²
9k 12k
Cross section
1.0 mm² (1.5 mm²)
AWG18 (AWG16)
1.0 mm² (1.5 mm²)
AWG18 (AWG16)
1.0 mm² (1.5 mm²)
AWG18 (AWG16)
1.0 mm² (1.5 mm²)
1.0 mm² (1.5 mm²)
1.0 mm² (1.5 mm²)
NOTE:
For some models, the cables have been connected by the manufac-
turer to the main circuit board of the interior unit without terminal strips.
Operation
Tableside Control
If the remote control is not functioning or maintenance is required, pro-
ceed as follows:
Tightening torque (N × m)
7 - 9
25 - 30
15 / 18k
1.5 mm²
AWG16
1.5 mm²
AWG16
1.5 mm²
AWG16
1.5 mm²
1.5 mm²
1.5 mm²
0.75 mm²
0.75 mm²
18 / 22k
1.5 mm²
AWG16
1.5 mm²
AWG16
1.5 mm²
AWG16
1.5 mm²
1.5 mm²
1.5 mm²
17.12.20