Publicidad
Idiomas disponibles
Idiomas disponibles
2. Insert 2 × R03 "AAA" 1.5 V batteries. Please ensure that the polarity is
correct. (See the bottom of the battery compartment)
NOTE:
• Child Safety Lock: Press the
time to activate the child safety lock.
• Turn the display on / off: Press and hold the ECO button
3. Point the remote control at the air conditioning unit.
NOTE:
• Make sure there are no objects / obstructions located in the space
between the remote control and the signal receiver in the interior
unit.
Adjusting the Air Flow
The air flow will be evenly distributed as it escapes into the room. Options
are available for optimization of the flow direction.
The
button activates the air directing flap (1). The air flow is directed from
above to below to guarantee even distribution of the air throughout the room.
The air deflectors (2) must be positioned manually and are located under the
air directing flaps. These make it possible to direct the air flow towards the
right or the left.
CAUTION:
• Orientation of the air deflector must occur while the appliance is switched off.
• Never position the air directing flaps manually (i. e. by hand). This can result in serious damage.
• Never insert fingers, sticks or other objects into the air inlet / outlet openings. This can result in material damage and personal injury.
NOTE:
• Please note that for design reasons, not all features can be viewed in the remote control display in each operating mode. By pressing the
OPTION button, you can discover which features are available for individual operating modes.
• MODE button Select an operating mode
• OPTION button Select a feature
Cooling Mode (COOL)
Cooling mode permits simultaneous cooling of the room and reduction
of air humidity.
1. To activate cooling mode, press the MODE button until "COOL" ap-
pears in the remote control display. The cooling function will activate
if the temperature selected is lower than the temperature in the room.
(Selection using the
and
buttons.)
2. To optimize the air conditioning feature, adjust the temperature, the
speed and the air flow direction by pressing the appropriate buttons.
Heating Mode (HEAT)
Heating mode makes it possible to heat the room.
1. To activate heating mode, press the MODE button until "HEAT" ap-
pears in the remote control display. The heating function will activate if
the temperature selected is higher than the temperature in the room.
(Selection using the
and
buttons.)
2. To optimize the heating feature, adjust the temperature, the speed
and the air flow direction by pressing the appropriate buttons.
NOTE:
• If the appliance is equipped with an electric heater, then this will
delay activation of the application for a few minutes.
• An automatic thawing function may activate during heating mode.
This thawing function is indispensable for the cleaning of the appli-
ance. Frost residue on the condenser is removed in order to restore
its full heat exchange capacity. This procedure normally takes 2 - 10
minutes. The fan will stop operating during defrosting. After defrost-
ing, the appliance will automatically revert to heating mode.
98
CL6045QCCB_IM
and
buttons down at the same
NOTE:
• Never leave the remote control exposed to direct sunlight for long
periods of time.
• Use and store the remote control at a distance of at least one meter
from the television set or other electrical appliances.
Switch On / Off
Press the
button to switch off the appliance.
Press the
button again to switch the appliance on again.
Switching the Appliance on Automatically (
To program the appliance to switch on automatically, the appliance must
be turned off.
1. Press the OPTION button.
2. Use the arrow buttons to select
the remote control display.
3. Press the OPTION button again and use the arrow buttons
to adjust the desired time.
4. Confirm your selection using the OPTION button.
NOTE:
• To interrupt the adjusted function, repeat the steps described
above.
• The Timer feature can be adjusted for 30-minute intervals
Switching the Appliance Off Automatically (
To program the appliance to switch off automatically, the appliance must
be turned on.
1. Press the OPTION button.
2. Use the arrow buttons to select
the remote control display.
3. Press the OPTION button again and use the arrow buttons
to adjust the desired time.
4. Confirm your selection using the OPTION button.
NOTE:
• To interrupt the adjusted function, repeat the steps described
above.
)
and
until "
" appears on
and
)
and
until "
" appears on
and
17.12.20
Publicidad
