Livington Multi Scrubber Instrucciones De Uso página 7

the plug and pull on it. Keep the charging cable
away from heat and sharp edges.
• Do not use the device in environments where
explosive or flammable gases and liquids are
present.
• If unusual noises, smells, smoke or faults
occur during operation, switch the device off
immediately, and remove the plug from the socket.
• Make sure that the device is switched off before
changing accessories or charging the device.
• Do not charge the battery when the ambient
temperature is below 5°C or above 40°C.
• Ensure that hair, loose clothing and body parts are
kept away from moving parts.
PURPOSE OF USE
This device is suitable for cleaning floors and other hard surfaces such
as tiles, parquet, stone, etc.
The device is intended for domestic use, and is not for commercial or
industrial purposes.
Use the device only as described in the operating instructions. Any
other type of use is to be considered improper use.
BEFORE FIRST USE
Important: Check that the package contains all components and
ascertain whether they have been damaged in transit. In the event
of damage, you should refrain from using the product, and contact
customer service immediately.
1. Before using the device, remove all transport protection devices
and stickers, etc. Never remove type shields or warning labels!
2. Charge the battery (see "Charging the battery").
3. Remove coarse dirt from the floors and surfaces that you intend
to clean.
CHARGING THE BATTERY
• Risk of short-circuit! Do not insert any electrically conductive
objects (e.g. screwdrivers) into the charging socket.
• Unplug the adapter from the socket when the device is not charging.
• The battery must be fully charged before it is switched on for the
first time, in order for the maximum charge capacity to be achieved.
• DO NOT charge continuously for more than 12 hours. This could
shorten the battery life.
INFO: It will take around 8 to 10 hours to charge the battery before
first use.
1. Remove the silicone cover from the charging socket (13) on the
motor unit (2).
2. Plug the adapter into the charging socket.
3. Plug the adapter into a functioning and easily accessible mains
socket. The indicator light (10) will light up red.
4. The indicator light flashes red while charging. After 5 hours of
charging, the indicator lamp lights up red (NO longer flashes) - this
indicates, that the charging process has finished.
M31774_LivingtonMultiScrubber_Manual_20211103_BS.indd 7 M31774_LivingtonMultiScrubber_Manual_20211103_BS.indd 7
5. First disconnect the adapter from the mains, and then from the device.
6. Place the silicone cover back into the charging socket.
ASSEMBLY
The motor unit of the Livington Multi Scrubber (2) can be used as both
a hand-held device and in combination with the telescopic pole and
frame for the motor unit (6+8).
Attaching/removing the telescopic pole:
• Place the motor unit in the frame (6). The safety lock must audibly
click into place on both the left and right sides. Make sure that it is
securely attached.
• To remove the motor unit, push the safety latch outward. This will
release the motor unit and allow it to be removed.
Attaching/removing the pad adapter and pads:
The correct structure can be found in #3 - from top to bottom:
• Motor unit (2)
• Pad adapter/attachment plate (4)
• Pad (nylon pad or microfibre pad - 3 or 5)
IMPORTANT INFO: THE PAD ADAPTER AND THE MICROFIBRE CLOTH
ARE ALREADY ATTACHED TO THE MOTOR UNIT AT DELIVERY!
Of course, you can separate the motor unit from the pad adapter and
then disconnect this from the pads, and put them back together again
- this is very simple:
• 6 magnets (12) are attached to the underside of the motor unit (2).
The pad adapter (4) must be attached to these magnets. Attach
the pad adapter to the motor unit. Make sure that the arrows on the
motor unit and the pad adapter are aligned and point towards each
other. The side with the Velcro fastener faces outwards.
• To remove the pad adapter from the motor unit, all you need to do
is pull on it.
Attaching/removing the cloths:
Select the desired cloth and attach it to the pad adapter using the
Velcro fastener. To remove the cloth, hold the pad adapter and pull on
the cloth.
Attaching and removing the detachable handle to/from the
telescopic pole #2
Insert the telescopic pole into the detachable handle, and rotate
it so that the pin meets the hole in the telescopic pole. To remove
the detachable handle, press down on the pin and pull it out of the
telescopic pole.
Attaching/removing the optional accessories
(ATTENTION: NOT INCLUDED IN DELIVERY CONTENTS)
The brushes do not require an adapter and can simply be attached
directly to the device using the magnets, and removed in the same way.
Suitable accessories for your Livington Multi Scrubber can be
purchased at www.mediashop.tv or by calling 0800 900 88 90 (free of
charge from DE, AT + CH).
USE | Do not use the device unless it has been fully and properly
assembled. Switch off the device before attaching or removing any
accessories. Do not use the device while it is connected to the charging
7
04.11.21 09:59 04.11.21 09:59