SafeWaze 020-6041 Manual De Instrucciones

Rescue Ladder Instruction Manual
020-6041
Rescue Ladder Rescue Ladder w/ Belay
22'
RESCUE LADDER
WARNING
This product is part of a personal fall arrest system, work positioning, suspension or rescue system.
The manufacturer's instructions must be provided to users of this equipment. The user must follow the
manufacturer's instructions for each component of the system. The user must read and understand these
instructions before using this equipment. Manufacturer's instructions must be followed for proper use
and maintenance of this equipment. Alterations to this product, misuse of this product, or failure to follow
instructions may result in serious injury or death.
IMPORTANT
Questions regarding the use, care, or suitability of this equipment for your application? Contact
SafeWaze.
IMPORTANT
Record identification information before using this product. Identification information may be found on
the equipment label. This information should be recorded in the "Inspection Log" located at the back of
this manual
Complies with OSHA 1910.66 and OSHA 1926.503
Ensure a written rescue plan, system and method are in place and easily accessible for rapid deployment and use.
Rescues may require specialized equipment or methods that are beyond the scope
of this product. For addtional Rescue information see ANSI Z359.4-2013
This manual is intended to meet the manufacturer's instructions as required by ANSI Z359
and should be used as part of an employee training program as required by OSHA.
User Information
Date of First Use:
Serial#:
Trainer:
User:
Do not throw away these instructions!
Read and understand these instructions before using equipment!
INTRODUCTION
Thank you for purchasing the SafeWaze Rescue Ladder. This manual must be read and understood in
its entirety, and used as part of an employee training program as required by OSHA or any applicable
state agency. This manual and any other instructional material must be available to the user of the
equipment. The user must understand how to safely and effectively use the Rescue Ladder, and all
rescue equipment used in conjuction with such.
APPLICABLE SAFETY STANDARDS
When used according to instructions, the SafeWaze Rescue Ladder fully complies with all applicable
ANSI Standards and OSHA Regulations. Applicable standards and regulations depend on the type of
work being done, and may include state-specific regulations. Refer to local, state, and federal (OSHA)
requirements for additional information concerning the governing of occupational safety regarding
Personal Fall Arrest Systems (PFAS).
WORKER CLASSIFICATIONS
Understand the definitions of those who work in proximity of or may be
exposed to fall hazards.
Qualified Person: "Qualified" means one who, by possession of a recognized degree, certificate,
or professional standing, or who by extensive knowledge, training, and experience, has successfully
demonstrated his ability to solve or resolve problems relating to the subject matter, the work, or the
project.
Competent Person: "Competent Person" means one who is capable of identifying existing and
predictable hazards in the surroundings or working conditions which are unsanitary, hazardous, or
dangerous to employees, and who has authorization to take prompt corrective measures to eliminate
them.
Authorized Person: "Authorized person" means a person approved or assigned by the employer to
perform a specific type of duty or duties or to be at a specific location or locations at the job site.
It is the responsibility of a Qualified or Competent person to supervise the job site and
ensure safety regulations are complied with.
2064
PRODUCT SPECIFIC APPLICATIONS
Purpose: The SafeWaze Rescue Ladder is designed to be used as a rescue system to return fall
victims to safety.
- A competent person shall train users on this equipment in accordance with OSHA
and ANSI.
- Never exceed a free fall distance of 6 ft. A free fall of more than 6 ft could cause
excessive arrest forces that could result in serious injury or death.
- The SafeWaze Rescue Ladder has a maximum capacity of ANSI 310 lbs
including any tools, clothing, accessories, etc..., OSHA 420 lbs, unless otherwise
rated by Safewaze.
020-6042
- Attachment of the SafeWaze Rescue Ladder can be made to the existing anchor point
or a new anchor location.
- The SafeWaze Rescue Ladder must be inspected prior to use, and after any rescue
operation.
- Safewaze Rescue Ladders shall be inspected by the end user prior to each usage and
by a Competent Person at least annually. These inspections shall be documented.
LIMITATIONS
22'
Fall Clearance: There must be sufficient clearance below the anchorage connector to arrest a fall
RESCUE LADDER
before the user strikes the ground or an obstruction. When calculating fall clearance, account for a
MINIMUM 2' safety factor, deceleration distance, user height, length of lanyard/SRL, and all other
applicable factors (See Figure 1).
***Diagram shown is an example
fall clearance calculation ONLY.
Required
distance
from
Anchorage
(18' total)
Height of harness dorsal
Swing Falls: Prior to installation or use, make considerations for eliminating or minimizing all swing
fall hazards. Swing falls occur when the anchor is not directly above the location where a fall occurs.
Always work as close to in line with the anchor point as possible. Swing falls significantly increase
the likelihood of serious injury or death in the event of a fall (See Figure 2).
COMPATIBILITY OF CONNECTORS
Connectors are compatible with connecting elements when they have been designed to work together
in such a way that their sizes and shapes do not cause their gate mechanisms to inadvertently open
regardless of how they become oriented. Connectors (hooks, carabiners, and D-rings) must be
capable of supporting at least 5,000 lbs. (22.2 kN). Connectors must be compatible with the anchorage
or other system components (See Figure 4). Do not use equipment that is not compatible.
Non-compatible connectors may unintentionally disengage (See Figure 3). Connectors must be
compatible in size, shape, and strength. Self-locking snap hooks and carabiners are required by ANSI
Z359 and OSHA guidelines. Contact Safewaze if you have any questions about compatibility
NOTE: SOME SPECIALITY CONNECTORS HAVE ADDITIONAL
REQUIREMENTS. CONTACT SafewazeWITH QUESTIONS.
FIGURE 3 - UNINTENTIONAL DISENGAGEMENT
1 - Non Compliant Part
I I
225 Wilshire Ave, Concord NC, 28025
FIGURE 1
For all applications: worker weight capacity range
(including all clothing, tools, and equipment) is
ANSI 130-310 lbs., OSHA 420 lbs.
Fall Clearance Diagram
Lanyard Length
(6' Total)
Deceleration
distance (4' total)
D-ring from
worker's feet
(6' total)
Safety factor
(2' total)
FIGURE 2
FALL-ARREST A
.
4 - And parts
disengage.
3 - Gate opens
2 - Gate presses
against
non-compliant
part
I I
Phone: 704-262-7893 Fax: 704-262-9051 Email: info@safewaze.com
Using a connector that is undersized or irregular in shape (1) to connect a snap hook or carabiner could
allow the connector to force open the gate of the snap hook or carabiner. When force is applied, the gate
of the hook or carabiner presses against the non-compliant part (2) and forces open the gate (3). This
allows the snap hook or carabiner to disengage (4) from the connection point.
MAKING CONNECTIONS
Snap hooks and carabiners used with this equipment must be double locking and/or twist lock. Ensure
all connections are compatible in size, shape and strength. Do not use equipment that is not compatible.
Ensure all connectors are fully closed and locked.
Safewaze connectors (snap hooks and carabiners) are designed to be used only as specified in each
product's user's instructions. See Figure 4 for examples of inappropriate connections. Do not connect
snap hooks and carabiners:
• To a D-ring to which another connector is attached.
• In a manner that would result in a load on the gate (with the exception of tie back hooks).
• NOTE: Large snap hooks must not be connected to objects which will result in a load on the gate if
the hook twists or rotates. Snap hooks marked with ANSI Z359.12 and are equipped with a 3,600 lb
(16 kN) gate. Check the marking on your snap hook to verify its compatibility.
NOTE: Large throat snap hooks must not be connected to standard size D-rings or similar
objects which will result in a load on the gate if the hook or D-ring twists or rotates, unless
the snap hook complies with ANSI Z359.12 and is equipped with a 3,600 lb (16 kN) gate.
Check the marking on your snap hook to verify that it is appropriate for your application.
• In a false engagement, where features that protrude from the snap hook or carabiner catch on the
anchor, and without visual confirmation seems to be fully engaged to the anchor point.
• To each other.
• By wrapping the web lifeline around an anchor and securing to lifeline except as allowed for Tie Back
models.
• To any object which is shaped or sized in a way that the snap hook or carabiner will not close and
lock, or that roll-out could occur.
• In a manner that does not allow the connector to align properly while under load.
FIGURE 4 - INAPPROPRIATE CONNECTIONS
SPECIFIC APPLICATIONS
Rescue/Confined Space: The Rescue Ladder is authorized for use in
Rescue/Confined Space applications. Rescue systems are utilized to
safely recover a worker from a confined location or after exposure to
a fall. Composition of rescue systems can vary based upon the type
of rescue involved. The structure to which a Anchor is attached must
A withstand loads applied in the directions permitted by the system of at
FALL-ARREST
least 3,000 lbs. NO free fall is permitted. For rescue applications, the
allowable attachment points to harness are Dorsal D-ring, Chest D-ring
and Shoulder D-rings.
22'
RESCUE LADDER
All above referenced applications have a worker weight capacity range of
ANSI 130-310 lbs (including all clothing, tools, and equipment), OSHA 420 lbs.
RESCUE LADDER COMPONENTS
FIGURE 5 - RESCUE LADDER COMPONENTS
020-6041
A
22'
B
RESCUE LADDER
C
D
A. Carabiner(s) B. Outer Bag C. 22' Rescue Ladder D. Belay Rope
I
Web: safewaze.com
020-6042
E
22'
Climber Lift
Pull
Rope
RESCUE LADDER
E. Rope Grab