Calibration; Ending The Flight; Rotor Guards; Cleaning, Repair And Storage - DELTA-SPORT QC-8608 Instrucciones De Manejo

Calibration

You may occasionally find that the quadcopter (1)
flies erratically and needs to be calibrated. In this
event, follow the steps below:
1. Place the powered-on quadcopter (1) on a
horizontal, level surface.
2. Simultaneously slide the throttle (2h) and the
control lever (2l) on the powered-on remote
control (2) towards yourself and at an angle
outwards. The indicator lights (1g) on the
quadcopter (1) will flash for approx. 3 seconds.
Once the indicator lights (1g) are steadily
illuminated, the calibration is complete and the
quadcopter is ready to fly.
NOTE: repeat the calibration if the
quadcopter still flies erratically in one
direction.

Ending the flight

1. Press the 'START/LAND' button (2i). The quad-
copter slowly descends and lands.
After the quadcopter (1) has landed safely,
switch it off in the proper sequence.
2. Press the on/off switch (1d) on the quadcopter
(1) to turn the quadcopter (1) off.
3. Press the on/off (switch) (2a) on the remote
control (2) to turn the remote control off.
4. Remove the rechargeable battery (3) (see
'Removing the rechargeable battery').

Rotor guards

The rotor guards (1c) act as protection against in-
juries (e.g. cuts, skin injuries or eye injuries) and to
protect against, or in the event of, collisions. These
are firmly mounted. If the rotor guards become
loose, firmly reattach them and check the function
and correct placement of the rotor guards (1c).
WARNING: never operate the quadcop-
ter (1) without rotor guards (1c)! So as not
to endanger yourself and/or other people and
animals, do not remove the rotor guards (1c)
arbitrarily!
40 GB/IE

Cleaning, repair and storage

CAUTION: before undertaking any
work on the quadcopter, the on/
off switch (1d) must be switched off and
the rechargeable battery (3) must be
removed.
The quadcopter (1) must always be kept dry, and
any dirt such as wool fibres, hair, dust, etc., must
be removed after every flight.
Use a dry cloth to dry the quadcopter; the elec-
tronics, rechargeable battery and motor must not
be exposed to water.
Store the quadcopter (1) in a dry, dust-free
location away from direct sunlight. The optimum
storage temperature is between 10°C and 25°C.
Disconnect the rechargeable battery connector
(3a) or the connection to the charging cable (4)
when not in use. Remove the batteries (5) from the
remote control.

Replacing the rotor blades (Fig. G)

Replace the rotor blades (A), (B) as soon as they
are damaged.
Use the tool (7) to remove the rotor blades (1a),
(1b) from the quadcopter (1).
NOTE: there are two different types of rotor
blades (A), (B). The rotor blades (A) rotate
clockwise, and the rotor blades (B) rotate
anti-clockwise. The rotor blades are shaded in
grey on the diagrams for clarity.
Both kinds are marked on the upper side with A or
B, which must be noted when replacing and must
match the markings on the quadcopter (1).
WARNING: if the rotor blades (A), (B)
are damaged, there is a risk of pieces
falling off during use and causing damage or
harming the environment.
Follow the steps below to change a rotor blade
(A), (B):
1. Attach the open side of the tool (7) under the
rotor blade (A), (B) and lift it off the quadcopter
(1).
2. Place the replacement rotor blade (A), (B) into
the same position that the damaged rotor blade
(A), (B) came out of.
3. Press the rotor blade (A), (B) with the other side
of the tool (7) securely onto the quadcopter (1).