Avenger B7030 BUCCANEER Manual De Instrucciones página 12

To check this, crank the stand up a few centimetres and press down the safety lever;
repeat this action a few times to ensure it functions correctly.
If the columns or the mechanism are iced up, try to de-ice but do not expose to direct flame or use a
de-icing fluid (joints and bearings could be affected by this).
SPARE PARTS
In the event on the product becoming defective, the unit should be returned to an authorised Videndum Media
Solutions service agent.
19 20 21 22
COLUMN REGULATION PROCEDURE
1. Make sure you have the stand with the column closed, with the legs open and level (use the bubble on the
upper cross).
2. Turn the wheels inwards to a radial position and activate the brake to prevent shifting. (fig. 19)
3. Extend the column to the maximum height without load and move it slightly back and forth, right and left
with the handle to see if it is well guided or if there are any plays. (fig. 20)
4. Lower the column until the guides are accessible but without completely closing everything. (fig. 21)
5. To adjust the various sections of the column, unscrew the screws of guides 1 and 2, advance the guide to
the required position and screw the guides back on. Do this on the desired columns. (fig. 22)
6. To recover the clearances of the base column, screw the dowels present on the side of the column (fig.
23) and reduce the lateral clearances. Act on the central grain (fig. 23). To recover the slack and adjust the
column in the front direction.
7. Once you have made the adjustment and made sure you have closed all the screws, extend the column
and check that the adjustment has been successful, if not repeat the procedure.
GREASING OPERATION 24
To grease the indicated area use a general grease spray.
For lifting chain use a general grease spray for chains
1. Wheel rotation locking pin "Y"
2. Thrust bearing between the wheel bracket and moveable leg stirrup "Z"
3. Pivot pin of the moveable leg stirrup "AA"
4. Lifting Chains "AB"
25
BRAKE MAINTENACE
Check the correct functioning of the braked wheels by attempting to force the movement of the wheel with the
brake applied, if the wheel starts moving when force is applied the brake must be adjusted:
1. Release the brake "AC"
2. Unlock the brake pad adjustment by unscrewing the locking nut "AD"
3. Adjust the brake pad by tightening or loosening the threaded pin until the pad touches the wheel, then
move the brake pad away from the wheel by loosening the threaded pin by ½ a turn "AE"
4. Engage the brake by pushing the lever and then lock the brake pad in position by tightening the locking nut
"AF" and "AG"
5. Release the brake again and make sure the wheel spins freely without touching the brake pad
6. Check the correct brake adjustment as explained above
Repeat the check for each wheel
LIFTING THE STAND WITH A WINCH OR LIFTING GEAR
To move the stand using a winch or other lifting gear, lift or lower the stand with a webbing sling (not included)
around and through the upper spider "AH"
While lifting or lowering, verify that the stand is well balanced and that the legs are securely fastened "AI"
Never load webbing slings beyond their maximum carrying capacity and check that it is correctly fixed to the
stand and to the lifting gear.
PRECAUTIONS
Do not use the product beyond the defined operating limitations.
GB
23
&
26
Do not tamper with or modify the product or parts thereof as doing so would compromise the product's opera-
tion and/or safety. Using a product that has been damaged, for example due to impact or accidental falls may
compromise its safe use.
In such cases, contact your retailer or the manufacturer directly through the customer service section on man-
frotto.com.
Dry the product after use in damp conditions to avoid triggering corrosion especially when using it near marine
environments.
The product is not designed to be used immersed in liquids.
⚠
The stand must not be left unattended or accessible to non-professionals.
EXCLUSION OF LIABILITY
The information contained in this document may be subject to variations over time.
If necessary, please check for updates to this manual in the Products area of the Manfrotto.com or Avenger.
com web site or request an updated copy to be sent to you through the Contact us area.
Videndum Media Solutions cannot be held liable for any damage that may, directly or indirectly, derive from
people, things or animals, as a consequence of the non-observance of all the instructions in this document (in
particular regarding installation, use and maintenance of the product), as well as injuries and damages resulting
from improper use or use that goes beyond the normal operating limitations.
Any variation or change made to the product without explicit permission from Videndum Media Solutions shall
automatically result in the exclusion of any liability on Videndum Media Solutions' part.
USER INFORMATION
Product disposal and packaging materials used:
Stand: The main structure is made of aluminium and steel; rubber protection
Packaging: Paper, cardboard, polystyrene inserts, polyethylene bags
To dispose of the product and its packaging, please refer to the regulations in force in the country in which the
product is being disposed of for the a aforementioned materials.
Thank you for purchasing a Videndum Media Solutions product.
Videndum Media Solutions guarantees that its products are suitable for the purpose for which they were de-
signed and free from defects in materials and workmanship. This warranty does not cover the product against
damage or improper use.
The duration of the Standard Warranty period is defined by the legislation in force in the country, state or region
in which the product is sold.
Please keep a copy of your product's proof of purchase, as it will be requested in case of repair.
The manufacturer reserves the right to make any changes to the product described in this manual, at any time
and without notice.
How to extend the warranty coverage:
In addition to the mandatory standard cover referred to above, Videndum Media Solutions offers a warranty ex-
tension of up to 5 years from this product's date of purchase. The warranty extension does not affect standard
mandatory coverage. To benefit from the warranty extension, you are required to register your purchase on our
web site: https://warranty.videndummediasolutions.com.
- 12 -
GB