Electrical Connection; Installations; Prepare Built-In Oven; Remove Oven Door(S) - KitchenAid 27 Manual Del Usuario

Electrical Connection

To properly install your oven, you must determine the type
of electrical connection you will be using and follow the
instructions provided for it here.
� Oven must be connected to the proper electrical voltage,
amperage, and frequency as specified on the model/serial/
rating plate. See the following illustration.
A. Model/serial/rating plate
� Models rated from 7.3 to 9.6 kW at 240 V (6.3 to 8.3 kW at
208 V) require a separate 40 A circuit. Models rated from
4.9 to 7.2 kW at 240 V (4.3 to 6.2 kW at 208 V) require a
separate 30 A circuit. Models rated at 4.8 kW and below at
240 V (4.2 kW and below at 208 V) require a separate 20 A
circuit.
� A circuit breaker is recommended.
� Connect directly to the fused disconnect (or circuit breaker
box) through flexible, armored or nonmetallic sheathed, copper
cable (with grounding wire). See the "Make Electrical
Connection" section.
� Flexible conduit from the oven should be connected directly to
the junction box.
� Do not cut the conduit. The length of conduit provided
is for serviceability of the oven.
� A UL listed or CSA approved conduit connector
must be provided.
� If the house has aluminum wiring, follow the procedure below:
Connect the aluminum wiring using special connectors and/or
tools designed and UL listed for joining copper to aluminum.
Follow the electrical connector manufacturer's recommended
procedure. Aluminum/copper connection must conform with
local codes and industry accepted wiring practices.
Be sure that the electrical connection and wire size are
adequate and in conformance with the National Electrical
Code, ANSI/ NFPA 70-latest edition or CSA Standards
C22.1-94, Canadian Electrical Code, Part 1and C22.2 No. O-
M91-latest edition, and all local codes and ordinances. A copy
of the above code standards can be obtained from: National
Fire Protection Association 1 Batterymarch Park Quincy, MA
02169-7471 CSA International 8501 East Pleasant Valley
Road Cleveland, OH 44131-5575.
10

INSTALLATIONS

Prepare Built-In Oven

1. Decide on the final location for the oven. Avoid drilling or
cutting into house wiring during installation.
WARNING
Excessive Weight Hazard
Use two or more people to move and install or uninstall
appliance.
Failure to do so can result in back or other injury.
2. To avoid floor damage, set the oven onto cardboard prior to
installation. Do not use handle or any portion of the front frame
for lifting.
3. Remember to remove bottom vent from the foam packing on
top of oven.
4. Remove the shipping materials and tape from the oven.
Remember to keep the corner posts and other materials
that may be needed for installation.
5. Remove the hardware package from inside the bag containing
literature.
6. Remove and set aside racks and other parts from inside the
oven.
7. Move oven and cardboard close to the oven's final location.

Remove Oven Door(s)

IMPORTANT: Use 2 hands to remove oven door. For double
ovens, repeat the process for each door.
1. Prior to removing the oven door, prepare a surface where you
will place it. This surface should be flat and covered with a soft
blanket, or use the corner posts from your packaging material.
2. Fully open the oven door.
3. Locate the oven door hinge locks in both corners of the oven
door, and rotate the hinge locks toward the oven door to the
unlocked position. If the door hinge lock is not rotated fully
(see illustration B), the door will not remove properly.
A. Oven door hinge lock in
locked position
Oven door hinge lock in
B.
unlocked position