Maintenance / Service; Declaration Of Conformity - SKIL MASTERS 1570 Manual Original

- always select a shallow planing depth and repeat the
planing and adjusting process until the required depth
is reached
• Chip outlet 6
- select desired chip outlet side (left or right) with switch
G
- connect vacuum cleaner with adapter H to selected
chip outlet as illustrated
- one may also connect dust bag J to the selected chip
outlet as illustrated
! do not attempt to remove any obstructions from
the chip outlet while knives are rotating
• Park rest K 7
- protects workpiece from damage when tool is put
aside
- will automatically fold backwards when planing
• Operating the tool
- adjust planing depth
- place tool on workpiece
! ensure that only the front shoe rests on the
workpiece and that the knives do not touch it
- switch on the tool by irst pressing knob L 2 (= safety
switch which cannot be locked) and then pulling
trigger M 2
! before the knives reach the workpiece, the tool
should run at full speed
- hold the tool irmly with both hands and guide it
forward in a continuous stroke
! while working, always hold the tool at the
grey-coloured grip area(s) 8
- use the tool with its base-plate on the workpiece
- do not tilt the tool in order to avoid unwanted planing
marks
- keep ventilation slots Q 2 uncovered
! before switching off the tool, you should lift it
from the workpiece
- switch of the tool by releasing trigger M
• Planing rabbets 9
- select required planing depth
- select rabbeting depth by using rabbeting depth
adjuster N
- place tool on workpiece
- start planing
- maximum rabbeting width 82 mm
- maximum rabbeting depth 15 mm
• When planing rabbets you will achieve better results by
using parallel guide P to adjust rabbeting width 0
APPLICATION ADVICE
• For chamfering edges use the V-grooves in the front shoe
!
- set knob D in "0" position
- select one of the 3 V-grooves
! always test out first on a piece of scrap material

MAINTENANCE / SERVICE

• Always keep tool and cord clean (especially ventilation
slots Q 2)
! disconnect the plug before cleaning
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skilmasters.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2012/19/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol @ will remind you of this when the need for
disposing occurs

DECLARATION OF CONFORMITY

• We declare under our sole responsibility that the product
described under "Technical data" is in conformity with the
following standards or standardization documents: EN
60745, EN 61000, EN 55014, in accordance with the
provisions of the directives 2004/108/EC, 2006/42/EC,
2011/65/EU
• Technical file at: SKIL Europe BV (PT-SEU/ENG1),
4825 BD Breda, NL
23.12.2013
NOISE/VIBRATION
• Measured in accordance with EN 60745 the sound
pressure level of this tool is 91 dB(A) and the sound
power level 102 dB(A) (standard deviation: 3 dB), and the
vibration 6.9 m/s² (hand-arm method; uncertainty
K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in EN 60745; it
may be used to compare one tool with another and as a
preliminary assessment of exposure to vibration when
using the tool for the applications mentioned
- using the tool for diferent applications, or with diferent
or poorly maintained accessories, may signiicantly
increase the exposure level
- the times when the tool is switched of or when it is
running but not actually doing the job, may signiicantly
reduce the exposure level
! protect yourself against the effects of vibration
by maintaining the tool and its accessories,
keeping your hands warm, and organizing your
work patterns
8