Publicidad
Idiomas disponibles
Idiomas disponibles
English
•
If the measurement is greater than the values shown
below, the laser must be serviced at an authorized
service center.
Distance
Between Walls
8'
10'
14'
20'
Distance
Between Walls
2.5 m
3.0 m
4.0 m
6.0 m
Using the Laser
Leveling the Laser
As long as the laser is properly calibrated, the laser is
self‑leveling. Each laser is calibrated at the factory to find
level as long as it is positioned on a flat surface within
average ± 4 ° of level. No manual adjustments are required.
If the laser has been tilted so much that it cannot self‑level
(> 4 °), the laser beam will flash. There are two flashing
sequences associated with the out of level condition.
•
Between 4 ° and 10 ° the beams flash with a constant
blink cycle
•
At angles greater than 10 ° the beams flash with a three
blink cycle.
When the beams flash THE LASER IS NOT LEVEL (OR PLUMB)
AND SHOULD NOT BE USED FOR DETERMINING OR MARKING
LEVEL OR PLUMB. Try repositioning the laser on a more
level surface.
Using the Pivot Bracket (Fig. I, J)
The laser has a magnetic pivot bracket
attached to the unit.
WARNING: Position the laser and/or wall mount on
a stable surface. Serious personal injury or damage to
the laser may result if the laser falls.
•
The bracket has a keyhole slot
a nail or screw on any kind of surface.
•
The bracket has magnets
be mounted to most upright surfaces made of steel or
iron. Common examples of suitable surfaces include
steel framing studs, steel door frames, and structural
steel beams. Before attaching the pivot bracket against a
stud
11
, place the Metal Enhancement Plate
opposite side of the stud.
Maintenance
•
To maintain the accuracy of your work, check the laser
often to make sure it is properly calibrated. See Field
Calibration Check.
•
Calibration checks and other maintenance repairs may be
performed by D
WALT service centers.
e
12
Allowable Distance
Between
and
a
b
1/8"
3/16"
1/4"
3/8"
Allowable Distance
Between
and
b
a
3.4 mm
4.2 mm
5.5 mm
8.2 mm
6
permanently
7
so it can be hung from
10
which allow the unit to
12
on the
•
When not in use, store the laser in the kit box provided.
Do not store your laser at temperatures below ‑5 ˚F
(‑20 ˚C or above 140 ˚F (60 ˚C).
•
Do not store your laser in the kit box if the laser is wet.
The laser should be dried first with a soft dry cloth prior
to storage.
Cleaning
Exterior plastic parts may be cleaned with a damp cloth.
Although these parts are solvent resistant, NEVER use
solvents. Use a soft, dry cloth to remove moisture from the
tool before storage.
Troubleshooting
The Laser Does Not Turn On
•
Fully‑charge the battery pack and then reinstall it in the
laser unit.
•
If the laser unit is heated above 120 ˚F (50 ˚C), the unit
will not turn on. If the laser has been stored in extremely
hot temperatures, allow it to cool. The laser level will
not be damaged by pressing the on/off button before
cooling to its proper operating temperature.
The Laser Beams Flash (Fig. K)
The lasers are designed to self‑level up to an average of
4 ° in all directions If the laser is tilted so much that the
internal mechanism cannot level itself, the laser beams will
flash indicating that the tilt range has been exceeded. THE
FLASHING BEAMS CREATED BY THE LASER ARE NOT LEVEL OR
PLUMB AND SHOULD NOT BE USED FOR DETERMINING OR
MARKING LEVEL OR PLUMB. Try repositioning the laser on a
more level surface.
If the laser battery pack has a low state of charge, the
beams will flash in a distinctive pattern of 3 quick flashes in
1 second, followed by constant light output for 4 seconds.
This flashing pattern indicates that the battery pack should
be replaced with a fully charged battery pack.
The Laser Beams Will Not Stop Moving
The laser is a precision instrument. Therefore, if it is not
positioned on a stable (and motionless) surface, the laser
will continue to try to find level. If the beam will not stop
moving, try placing the laser on a more stable surface. Also,
try to make sure that the surface is relatively flat, so that the
laser is stable.
Accessories (Fig. L - N)
Some laser kits are packaged with a drop ceiling bracket
The drop ceiling bracket contains a steel plate and attaches
to the magnetized pivot bracket
The drop ceiling bracket is equipped with both 1/4 ‑ 20 and
5/8 ‑ 11 female threads on the bottom of the unit).
This thread is to accommodate current or future D
accessories. Refer to Figure M and N for examples of
accessories sold seperately. Only use D
specified for use with this product. Follow the directions
included with the accessory.
WARNING: Since accessories, other than those offered
by D
WALT, have not been tested with this product, use
e
13
6
(Fig. L).
WALT
e
WALT accessories
e
.
Publicidad
