Descargar Imprimir esta página

Maintenance And Service; Maintenance And Cleaning; After Use/Storage; After-Sales Service And Application Service - Bosch AXT 22 D Manual Original

Ocultar thumbs Ver también para AXT 22 D:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 25
16 | English
Problem
Possible Cause
Machine beeps con-
The electronic control unit is faulty
tinuously for 10
seconds and does not
start, error cannot be
cleared pressing STOP
button (also two lights
are blinking the same
way on AXT 23 TC/25
TC/2550 TC)
Machine struggles to
Material to be shredded is wet and soft
grip material
Material to be shredded is wet and soft/Too much
Machine is blocked
soft green material has been fed into the machine
at once
Branches in collection
Pressure plate requires adjustment
box are not fully cut
Machine beeps and
Pressure plate is overtightened
motor won't start

Maintenance and Service

Maintenance and cleaning

Warning! Switch the product off and pull the mains
u
plug before any maintenance or cleaning. The same
applies when the mains cable is damaged, cut or en-
tangled.
Always wear protective gloves when using, adjusting
u
or cleaning the garden product.
Regularly check for obvious defects such as loose, dislodged
or damaged blades, loose fixings, and worn or damaged
components.
Check that covers and guards are undamaged and correctly
fitted. Carry out necessary maintenance or repairs before
using.
If the garden product should happen to fail despite the care
taken in manufacture and testing, repair should be carried
out by an authorised customer service agent for Bosch
garden products.
Removing the Pressure Plate (see figure J)
Warning! Switch the product off and pull the mains
u
plug before any maintenance or cleaning. The same
applies when the mains cable is damaged, cut or en-
tangled.
Always wear protective gloves when using, adjusting
u
or cleaning the garden product.
F 016 L94 417 | (28.10.2022)
Corrective Measure
Contact your Bosch Service Centre
Use the prodder to push the material into the ma-
chine
Clear jammed material (always wear protective
gloves)
Use the reverse button (see "Return Motion",
page 14)
(see "Pressure Plate Adjustment (see figure H)",
page 15)
Push in adjusting knob (10) and insert Allen key
(16) (sized 5 – not included) into the recess on
the end of adjusting screw and release anti clock-
wise (see figure I).
Then repeat pressure plate adjustment (see
"Pressure Plate Adjustment (see figure H)",
page 15)
The cutting system (15) and the pressure plate (14) have a
life expectancy of several years under normal usage and
when adjusted according to instructions.
Use the following to remove the pressure plate (14), to aid
cleaning or for replacement:
➊➋
Unscrew the pressure plate screw fully as shown.
Lift out pressure plate (14) using screw driver.
Assembly is carried out in reverse order. The pressure plate
(14) must then be readjusted (see "Pressure Plate Adjust-
ment (see figure H)", page 15).

After Use/Storage

The shredder must not be cleaned with high-pressure clean-
ers or running water.
Clean the exterior of tool thoroughly using a soft brush and
cloth. Do not use water, solvents or polishes. Remove all
grass and debris, especially from the ventilation slots (3).
Store the machine in a dry place. Do not place other objects
on top of the tool
Cable can be stored on the shredder as shown (only UK).
(see figure K).
The shredder can be stored as in figure B by removing the
chute assembly.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
Bosch Power Tools

Publicidad

loading

Este manual también es adecuado para:

Axt 25 dAxt 23 tcAxt 25 tcAxt 2550 tc