Ingersoll Rand 77A60P107 Manual Del Usuario página 18

PART NUMBER FOR ORDERING
1 Throttle Handle Assembly . . . . . . . . . . . . . . . . 77H–A160
2 Throttle Valve Assembly . . . . . . . . . . . . . . 88V60–A302
♦•
3 Seal (2) . . . . . . . . . . . . . . . . . . . . . . . . . C321–606
4 Inlet Bushing . . . . . . . . . . . . . . . . . . . . . . . 77H–38
♦•
5 Inlet Bushing Screen . . . . . . . . . . . . . . . . . 834–61
♦
6 Throttle Valve Spring . . . . . . . . . . . . . . . . . 77H–262
7 Oil Chamber Plug . . . . . . . . . . . . . . . . . . . R2–227
8 Throttle Valve Seat Support Assembly . . . 77H–A303
9 Valve Seat Screw . . . . . . . . . . . . . . . . . PS3–83
10 Valve Seat Lock Washer . . . . . . . . . . . . . . H54U–352
11 Valve Seat Washer . . . . . . . . . . . . . . . . 99V–155
♦•
12 Valve Seat . . . . . . . . . . . . . . . . . . . . . . R4–159A
♦
13 Valve Support Seal (2) . . . . . . . . . . . . . SPP101–743
14 Oiler Feeder Plug . . . . . . . . . . . . . . . . . 77H–75
15 Throttle Valve Seat Support Retainer . . . . . . . 77H–518
16 Throttle Lever Pin . . . . . . . . . . . . . . . . . . . . . . MR–100
17 Throttle Lever Assembly . . . . . . . . . . . . . . . . . 77H–A400
18 Lever Lock Pin . . . . . . . . . . . . . . . . . . . . . R100B–120
19 Lever Lock Spring . . . . . . . . . . . . . . . . . . . DG120–405
20 Lever Lock . . . . . . . . . . . . . . . . . . . . . . . . . DG120–402
21 Coupling Nut . . . . . . . . . . . . . . . . . . . . . . . . . . 77H–282
# 22 Controller Assembly (Consists of
Controller and Rear End Plate Assembly)
for 77A45W109 . . . . . . . . . . . . . . .
for 77A60W107, 77A60P107,
77A60P107M, 77A60P109 and
77A60P109M . . . . . . . . . . . . . . . . .
for 77A25F107, 77A75P107 and
77A75P107M . . . . . . . . . . . . . . . . .
23 Rear End Plate Assembly (consists of
rear end plate, rotor bearing and
required spacers) . . . . . . . . . . . . . . . . . . . . 77H–A12
♦•
24 Rear End Plate Gasket . . . . . . . . . . . . . . . . . . . 77H–739
25 Cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77H–3
* Not illustrated.
♦ Indicates Tune–up Kit part.
• To keep downtime to a minimum, it is desirable to have on hand certain repair parts. We recommend that you stock one (pair or set) of each part indicated by a
bullet (•) for every four tools in service.
# Early models of these Grinders had Rotors and Controller Assemblies with left–hand threads. If you have a model with left–hand threads, contact
Ingersoll–Rand when ordering replacement parts.
+ Whenever a new Angle Arbor Housing is installed, select the correct Nameplate from the Nameplate Kit (43A) and attach it to the Housing with the Nameplate
Screws (43B).
26 Rotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77H–53RH
♦ • 27
Vane Packet (set of 4 Vanes) . . . . . . . . . . . . . . 77H–42–4
• 28
Front End Plate . . . . . . . . . . . . . . . . . . . . . . . . 77H–11
29 Front Rotor Bearing . . . . . . . . . . . . . . . . . . . . . 77H–24
30 Cylinder Dowel . . . . . . . . . . . . . . . . . . . . . . . . 77H–98
31 Bevel Pinion Driver
32 Internal Gear . . . . . . . . . . . . . . . . . . . . . . . . . . 77H–406
33 Bevel Pinion Driver Bearing . . . . . . . . . . . . . . WFS182–97
34 Planet Gear Shaft (2) . . . . . . . . . . . . . . . . . . . . G700–191
35 Rotor Pinion . . . . . . . . . . . . . . . . . . . . . . . . . . . 77H–17
36 Planet Gear Assembly (2) . . . . . . . . . . . . . . . . 77H–A10
37
38 Thrust Spacer . . . . . . . . . . . . . . . . . . . . . . . . . . 77A–104
39 Bevel Pinion Bearing Assembly . . . . . . . . . . . 77A–A510
40 Matched Gear Set (Bevel Gear
and Pinion not sold separately) . . . . . . . . . . . . 77A–A552
41 Motor Spacer . . . . . . . . . . . . . . . . . . . . . . . . . . 77E–208–H8
42 Arbor Coupling . . . . . . . . . . . . . . . . . . . . . . . . 66H–304
+ 43 Angle Arbor Housing
77H90–A524RH 43A
77H120–A524RH 43B
*
77H150–A524RH
PART NUMBER FOR ORDERING
for 77A25F107 . . . . . . . . . . . . . . . .
for all others . . . . . . . . . . . . . . . . . .
Planet Gear Bearing (one for each gear) . . G700–654
for models ending in –EU . . . . . . .
for all other models . . . . . . . . . . . .
Nameplate Kit
for models ending in –EU . . . . . . .
for all other models . . . . . . . . . . . .
Nameplate Screw (4) . . . . . . . . . . . . . . BN403–302
Warning Label
for Grinders ending in –EU . . . . . .
for all other Grinders . . . . . . . . . . .
for Sanders and Polishers ending
in –EU . . . . . . . . . . . . . . . . . . . . . .
for all other Sanders and Grinders .
77A–8
77A–7
77A–EU–A40–P10
77A–A40–P10
77A–EU–K301
77A–K301
EU–99
WARNING–4–99
EU–99
WARNING–5–99