Descargar Imprimir esta página

Dremel 910 Traducción De Las Instrucciones Originales página 4

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 32
SPECIFICATIONS
Model number
910
920
Input
5W
5W
Voltage
------------- 100-240V ----------------
Glue temperature
• low (LO)
-
105°C
• high (HI)
165°C
-
Glue stick Ø
7 mm
7 mm
Weight
0.2kg
0.2kg
Use completely unrolled and safe extension
cords with a capacity of 5 Amps.
Always check that the supply voltage is
the same as the voltage indicated on the
nameplate of the tool.
GENERAL
The glue gun is intended for the quick gluing of
clean, dry and grease-free materials with glue
heated to its melting point.
A. Nozzle
B. Glue stick
C. Feed trigger
D. Stand
E. Temperature switch (930)
F. On/off switch with indicator light (940)
G. Detachable cord (940)
H. Stand release button (940)
DRIP-CONTROL FUNCTION
This prevents the glue from dripping when the
glue gun is at operating temperature.
USE
ON/OFF
Switching on
Plug the tool into into a standard 230 V
electrical outlet.
Once the tool is plugged in, it is on and
heating (910/920/930)
Adjust switch E to low or high temperature
setting; consult with glue stick package to
determine appropriate temperature (930)
Connect the power cord to the tool (940)
Switch the tool on with the main switch;
indicator light F will let you know the tool is
on and heating (940)
Switching off
Pull the mains plug (910/920/930)
930
940
Allow the tool to cool completely before storing.
7W
11W
The hot nozzle can cause damage.
PREPARATIONS FOR GLUING
105°C
-
165°C
195°C
7 mm
11/12 mm
0.2kg
0.3kg
GLUING
4
!
glue to come into contact with persons or
animals. If hot glue touches the skin,
immediately hold the spot for some
minutes under a stream of cold water. Do
not try to remove the glue from the skin.)
910 / 920 / 930
940
NOTE: For your first use, you may need to load
up to two full glue sticks before glue begins
to flow.
GLUE STICKS
Dremel also supplies glitter and colour sticks for
decorative purposes. These sticks have been
specially developed for creative projects and
low temperature (105°C).
The colour sticks can also be used for sealing
decorations. To be able to quickly change
4
Switch the tool off with switch F; pull the
mains plug (940)
The surfaces to be glued must be clean, dry
and free of grease.
Roughen smooth surfaces before gluing.
Do not use inflammable solvents for
cleaning.
The ambient temperature and the work
piece to be glued must not be colder than
+5°C or warmer than +50°C.
Warm rapidly cooling materials (e.g. steel)
for better adhesion.
DANGER OF BURNING (The glue
and the nozzle tip become very hot.
Do not allow the nozzle tip or hot
Allow the tool to reach operating
temperature before using (approximately
5 minutes).
Insert glue stick B.
Press feed trigger C.
Once the cord is detached, the tool remains
operable for 5 minutes, before it needs to
heat up.
Squeeze trigger C to apply glue onto
desired surface.
Apply parts together.
Allow glue to cool before handling object
or surface.
5
co
3 c
GG
GG
GG
GG
GG
GG
GG
NO
tem
wo
CH
CH
ST
Wh
Alw
Wh
"up
M
UN
RE
IN
WH
HA
Alw
pro

Publicidad

loading

Este manual también es adecuado para:

920930940