Environmental Protection; Technical Data - Metabo W 18 LT BL 11-125 Instrucciones De Manejo

10. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
- Quick clamping nut (without tools) (1) (see
page 2 fig. A)
- Dust filter (13)
The fine mesh filter prevents coarse particles from
entering the motor housing. Regularly remove and
clean (see page 2 fig. B).
- 2-hole nut (23) (see page 2 fig. G)
- Cutting guard clip/guard for cut-off grinding
(see page 4 fig. I)
Designed for working with cutting discs,
diamond cutting discs. With attached
cutting guard clip, the guard
turns into a cutting guard (see
page 4 fig. I).
- Dust extraction shroud clip (see page 4 fig. J)
It is intended for connecting a suitable extraction
unit when cutting mineral materials, such as
reinforced concrete and masonry exclusively with
diamond cutting discs, without using water.
- Dust extraction shroud (see page 4 fig. K)
Designed for cutting through stone slabs with
diamond cutting discs. With nozzle for extracting
stone dust using a suitable extraction unit.
- Dust extraction shroud* for surface grinding
Intended for grinding of concrete, screed, wood and
plastics with diamond cup wheels and/or fibre discs
and suitable hook and loop sanding pads. With
nozzle for extracting stone, wood and plastic dust
using a suitable extraction unit. Not suitable for
extracting sparks or for grinding of metals (see page
4 fig. L).
- Multi-position bar (26) for side handle
Permits diverse handle positions (see page 4 fig.
M).
- Hand protection
Intended for work with backing pads, hook and loop
packing pads (sanding pads), wire brushes and
diamond drill bits for tiles.
Install the hand guard under the side handle (see
page 4 fig. N).
- safety bracket**
Order no.: 628967000
- safety connection**
Order no.: 628965000
- bow handle (27)
Order no.: 623262000
- Battery packs:
Order no.: 625368000 5.5 Ah (LiHD)
Order no.: 624990000 5.5 Ah (LiHD)
Order no.: 625369000 8.0 Ah
Order no.: 624990000 5.5 Ah (LiHD
4991000 10,0 Ah (LiHD)
etc.
- Chargers: ASC 55, ASC 145, etc.
* May only be used in conjunction with the
2-hole nut
(LiHD)O
DS)rder no.:
** May only be used on machines with
paddle switch/with dead man function.
For a complete range of accessories, see
www.metabo.com or the accessories catalogue.
11. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.

12. Environmental Protection

The sanding dust generated may contain
hazardous materials: do not dispose of dust with
household waste, but at a special collection point
for hazardous waste.
Packaging materials must be disposed of according
to their labelling in accordance with municipal
guidelines. Further information can be found at
www.metabo.com in the "Service" section.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Battery packs must not be disposed of with regular
waste! Please return faulty or used battery packs to
your Metabo dealer!
Do not throw battery packs into water.

13. Technical Data

Explanatory notes on the specifications on page 3.
Subject to change in accordance with technical
progress.
U = Voltage of battery pack
D =max. diameter of accessory
max
t = max. permitted thickness of the clamping
max,1
shank on accessory when using two-hole
nut (23)
t = max. permitted thickness of the clamping
max 2
shank on accessory when using a quick
clamping nut (1)
t = roughing disc/cutting disc:
max,3
max. permitted thickness of accessory
M = Spindle thread
l = Length of the sanding spindle
n = No-load speed (maximum speed)
n = no-load speed (adjustable)
v
m = Weight (with smallest battery pack)
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on operating conditions, the
ENGLISH en
13