Drying Programmes Table; 6/ Maintenance And Cleaning - Selecline 600103364 Manual De Utilización

DRYING PROGRAMMES TABLE

Programme
Extra
Cotton
Standard
Less
Extra
Mix
Standard
Extra
Synthetics
Standard
1H
Note: Select the suitable
1. During the last 3 minutes of the drying cycle, there is no heating to cool down the load. (Exception: The cool down time is
10 minutes for the 1H programme.)
2. If the Anti-Crease option is selected, the entire anti-crease cycle will take 2 hours. Without the Anti-Crease option, the cycle
will end after 30 minutes.
3. The room temperature and humidity will influence the drying time.
4. Check the clothes care label and select the appropriate programme accordingly.
5. Recommendation: For a load of less than 0.5 kg, select the 1H programme and the Extra drying level for drying.
CONSUMPTION DATA
Programme
Cotton standard
Cotton standard
Synthetic standard
Note:
• Thick or multi-layered fabrics, e.g. jackets, etc., are not easy to dry. You had better choose the Cotton Extra programme.
• As uneven material, thick and multi-layered clothes are not easy to dry, it is better to choose the appropriate time drying
programme to completely dry them if some parts of the clothes are still damp after the programme finishes.
•  All data are measured in accordance with EN 61121. The actual consumption may differ from the values given in the table,
depending on the amount of the laundry, type of fabric, residual moisture, and any additional functions selected.

6/ MAINTENANCE AND CLEANING

SAFETY RESET
1. This tumble dryer has a safety cut-out switch which is activated by temperature.
2. If the tumble dryer does not heat up, reset it. Press the "safety reset" button and wait a minimum of 10 minutes before
restarting the appliance.
Note: The safety reset button is on the backboard of the tumble dryer.
3. The most common reason for the tumble dryer to overheat is a blocked filter.
4. Clean the lint filter after each cycle to prevent overheating of the tumble dryer.
The cut-out switch may operate for the following reasons:
• The lint filter is blocked.
• Exhaust outlets are blocked at the back of the dryer.
• Poor ventilation in the room. Open the windows or the door.
• Lightweight garment e.g. handkerchief, sucked over the filter.
SAFETY RESET BUTTON
Use your finger or a pencil to press the button until you feel its click.
Note: The safety reset button is on the backboard of the tumble dryer.
LINT FILTER CLEANING
The lint which is created by the drying process is collected in the lint filter in the
after each drying cycle. Remove the lint filter by pulling it straight up.
1. Cleaning whilst dry
Use a cloth or your fingers to remove the lint from the surface of the filter. Remove any lint from the hollow
part of the door opening. Also, clean the seal with a damp cloth. Once clean, push the lint filter back into the
door holder until it clicks into place. Ensure it is facing the correct way.
2. Cleaning with water
If there is still a great deal of compacted lint on the filter after cleaning it as described above, rinse the filter
under hot, running water. Dry the lint filter carefully and thoroughly before installing it.
Maximum load
7.0 kg
For the complete drying of single or multi-layer cotton laundry for direct
storage.
7.0 kg
7.0 kg For single-layer cotton laundry that is to remain damp for ironing.
3.5 kg For thick or multi-layer mixed fabrics to be dried completely.
3.5 kg For mixed fabrics from cotton and synthetics.
3.5 kg For thick or multi-layer synthetic fabrics to be dried completely.
To dry thin synthetic textiles, which are not ironed, such as easy care
3.5 kg
shirts, baby cloths or socks.
1.0 kg To dry individual items.
programme and drying level according to the type and capacity of the fabric.
Capacity Spin speed/Residual humidity
7.0 kg 1000 rpm/60%
3.5 kg 1000 rpm/60%
3.5 kg 800 rpm/40%
Application/Properties
Drying time
142 min
75 min
47 min
door. Clean the lint filter
9
EN
Energy consumption
4.49 kWh
2.27 kWh
1.45 kWh
Safety reset button