Chicco Comfy Wave Manual De Instrucciones página 11

• Do not leave small objects that could
be ingested by the child on the reclined
cradle.
• Do not use the reclined cradle outdoors
or in a damp environment.
• If the baby cradle is left exposed to direct
sunlight for an extended period of time,
allow it to cool down before placing your
child inside.
• Prolonged exposure to direct sunlight can
cause the fabric to fade.
• When not in use, keep the reclined cradle
out of the reach of children and unplug the
transformer putting it in a safe place and
out of reach of children.
WARNINGS ELECTRICAL PARTS
The motorized mechanism that moves
the reclined cradle and the sound panel
are both powered by the transformer and
power cable.
• WARNING: Long cable. Strangling
hazard.
• WARNING: The transformer must only
be plugged into the mains outlet by
an adult, and the cable jack must only
be plugged into the reclined cradle by an
adult.
• WARNING: The control panel must only
be switched on and regulated by an adult.
• WARNING: The transformer used with the
product must be inspected periodically to
ensure that the cable, plug, sheath, and
other components are not damaged, and
it must not be used if damaged.
• WARNING: The product must only be
used with the recommended transformer.
• Do not recklessly leave the product under
the rain, water infiltration damages the
electronic circuit.
• WARNING: Only use power transformers
that conform to EN 61558-2-7: 2007 or EN
61558-2-16:2009+A1:2013.
LIST OF COMPONENTS
A. Base with electronic panel
A1. Rocking device
A2. Jack socket
B. Electronic panel
B1. Power button
B2. Timer button
B3. Button for starting-changing music / adjusting volume
B4. Button for stopping music / locking and repeating latest
tune in a loop
B5. Reduce speed button
B6. Increase speed button
B7. Change movement button
C. Feet
C1. Front foot
C2. Rear foot
C3. Screws for fastening feet (x6)
D. Arch for adjusting inclination
D1. Inclination adjustment release button
D2. Release seat from base button
E. Seat
E1. Head area plastic insert with pin
E2. Foot area plastic insert with pin
E3. Toybar release button
E4. Toybar fastening point
F. Seat lining
F1. Seat strap release buckle
F2. Straps
G. Safety harness
G1. Crotch strap/abdominal restraint
G2. Shoulder straps
G3. Shoulder strap release buttons
G4. Abdominal restraint adjustment straps
H. Toybar
H1. Hanging toys
H2. Release button fastening point
I. AC Adaptor
I1. Jack connector
FIRST ASSEMBLY
1. Insert the front foot "C1" in the base "A" (Fig. 1), screw the 3
screws "C3" into their holes (Fig. 2).
2. Insert the rear foot "C2" in the base "A" (Fig. 3), screw the 3
screws "C3" into their holes (Fig. 4).
3. Flip the seat "E" upside down, insert the unjointed section of
the inclination adjustment arch "D" into the foot area plastic
insert "E2" (Fig. 5) until the fastening pin clicks in place (Fig.
6). Repeat the operation for the jointed section of the adjust-
ment arch "D" connecting it to the head area plastic insert
"E1" (Fig. 7) until the fastening pin clicks in place (Fig. 8).
4. Fasten the "F1" buckles behind the seat.
5. Now fasten the seat, connecting it to the rocking device
"A1" on the base (Fig. 9).
6. Assemble the toybar "H" fastening the connector "H2" to
the appropriate connection point "E4", connect the hole on
the toybar to the appropriate button "E3" first, and, subse-
quently, rotate externally (Fig. 10-11).
USING THE SAFETY HARNESS
7. At first use, the safety harnesses "G" will already be fastened.
The crotch strap/abdominal restraint "G1" cannot be discon-
nected, but its height can be adjusted. To release the shoul-
der straps "G2" press the two release buttons "G3" (Fig. 12).
At this point the child can be placed inside, the shoulder
straps will need to be fastened by inserting the prongs into
11