Ec Declaration Of Conformity; Instruction Manual; General Power Tool Safety Warnings - Makita DHR182 Manual De Instrucciones

Vibration
The following table shows the vibration total value (tri-axial
vector sum) determined according to applicable standard.
Work mode Vibration
emission
2
Hammer 11.4 m/s
drilling into
2
12.5 m/s
concrete
(a )
h, HD
2
Hammer 10.6 m/s
drilling into
2
11.6 m/s
concrete with
DX05 (a )
h, HD
2
Chiselling (a 9.3 m/s
h,
)
CHeq 2
11.5 m/s
* The test condition of recommended practical operation
meets EN 62841-2-6, except for the following points:
• Feed force is applied to the switch handle (main
handle) for working accuracy and efficiency.
• The side grip/handle (auxiliary handle) is held to
keep balance of the tool.
NOTE: The declared vibration total value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
NOTE: The declared vibration total value(s) may also
be used in a preliminary assessment of exposure.
WARNING:
The vibration emission during actual
use of the power tool can differ from the declared val-
ue(s) depending on the ways in which the tool is used
especially what kind of workpiece is processed.
WARNING:
Be sure to identify safety measures
to protect the operator that are based on an estimation
of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as the
times when the tool is switched off and when it is run-
ning idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only
The EC declaration of conformity is included as Annex A
to this instruction manual.
SAFETY WARNINGS

General power tool safety warnings

WARNING:
Read all safety warnings, instruc-
tions, illustrations and specifications provided
with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or
serious injury.
Uncer- Applicable
tainty (K) standard
/ Test
condition
2
1.5 m/s EN62841-2-6
2
2.2 m/s Recom-
mended practi-
cal operation*
2
1.5 m/s EN62841-2-6
2
1.5 m/s Recom-
mended practi-
cal operation*
2
1.5 m/s EN62841-2-6
2
2.0 m/s Recom-
mended practi-
cal operation*
Save all warnings and instruc-
tions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
CORDLESS ROTARY HAMMER
SAFETY WARNINGS
Safety instructions for all operations
1. Wear ear protectors. Exposure to noise can
cause hearing loss.
Use auxiliary handle(s), if supplied with the
2.
tool. Loss of control can cause personal injury.
Hold the power tool by insulated gripping sur-
3.
faces, when performing an operation where the
cutting accessory may contact hidden wiring.
Cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
Safety instructions when using long drill bits with
rotary hammers
1. Always start drilling at low speed and with the bit
tip in contact with the workpiece. At higher speeds,
the bit is likely to bend if allowed to rotate freely without
contacting the workpiece, resulting in personal injury.
2. Apply pressure only in direct line with the bit
and do not apply excessive pressure. Bits can
bend, causing breakage or loss of control, result-
ing in personal injury.
Additional safety warnings
Wear a hard hat (safety helmet), safety glasses and/
1.
or face shield. Ordinary eye or sun glasses are NOT
safety glasses. It is also highly recommended that
you wear a dust mask and thickly padded gloves.
Be sure the bit is secured in place before
2.
operation.
Under normal operation, the tool is designed to pro-
3.
duce vibration. The screws can come loose easily,
causing a breakdown or accident. Check tightness
of screws carefully before operation.
In cold weather or when the tool has not been
4.
used for a long time, let the tool warm up for
a while by operating it under no load. This
will loosen up the lubrication. Without proper
warm-up, hammering operation is difficult.
5. Always be sure you have a firm footing. Be sure no
one is below when using the tool in high locations.
6. Hold the tool firmly with both hands.
7. Keep hands away from moving parts.
8. Do not leave the tool running. Operate the tool
only when hand-held.
9. Do not point the tool at any one in the area
when operating. The bit could fly out and
injure someone seriously.
10. Do not touch the bit, parts close to the bit, or work-
piece immediately after operation; they may be
extremely hot and could burn your skin.
11. Some material contains chemicals which may
be toxic. Take caution to prevent dust inhala-
tion and skin contact. Follow material supplier
safety data.
12 ENGLISH