Publicidad
Idiomas disponibles
Idiomas disponibles
SETUP INSTRUCTIONS
This is the safety alert symbol used for the SETUP INSTRUCTIONS section of this manual to alert you to potential personal
injury hazards. Obey all instructions to avoid possible injury or death.
1.
Attach legs (#19) to top plate (#11) with hardware (#12, #13 and #14) as shown on the exploded view drawing on page 5.
Do not tighten hardware.
2.
Attach small braces (#16) to mid plate (#15) with hardware (#12, #13 and #14) as shown on the exploded view drawing on page 5.
Do not tighten hardware.
3.
Attach opposite ends of small braces (#16) to legs (#19) with hardware (#12, #13 and #14) as shown on the exploded view
drawing on page 5. Do not tighten hardware.
4.
Attach mid braces (#17) to the legs (#19) with hardware (#2) and (#13) as shown on the exploded view drawing on page 5. Do not
tighten hardware.
5.
Attach long braces (#18) to the legs (#19) with hardware (#2 and #13) as shown on the exploded view drawing on page 5. Do not
tighten hardware.
6.
Tighten hardware mentioned in steps 1 through 5 starting with step 1 first.
7.
Install the spring pin (#7) in the hole located at the bottom of the screw rod (#6). Feed the screw rod (#6) up through the post (#8)
as shown on the exploded view drawing on page 5.
8.
Place the bearing assembly (#5) onto the threads of the screw rod (#6).
9.
Thread the handle (#4) onto the screw rod (#6).
10 Install the saddle (#1) on top of the screw rod (#6) and secure them together with the bolt (#2).
11. Place the post (#8) down through the top of the top plate (#11) and then through the mid plate (#15). Raise the post to the desired
height and secure it to the top plate with the detent pin (#10) and pin clip (#9).
OPERATING INSTRUCTIONS
This is the safety alert symbol used for the OPERATING INSTRUCTIONS section of this manual to alert you to potential
personal injury hazards. Obey all instructions to avoid possible injury or death.
1.
Make sure the vehicle is properly supported, stable and at the required work height before positioning the stand(s) under the
vehicle component to be supported.
2.
Consult the lift and vehicle manufacturer for the proper positioning of the under hoist stand.
3.
Once the stand(s) has been positioned properly under the vehicle, hold the stand's saddle in place with one hand while
turning the spin handle in a clockwise direction with the other hand. Remove the one hand from the stand's saddle when it comes
close to making contact with the vehicle.
4.
Continue turning the stand's spin handle in a clockwise direction until it applies light pressure against the component. This
pressure should not exceed what is required to support the vehicle. Excessive pressure might cause the vehicle or its
component to become unstable.
5.
Before removing the stand from the vehicle, make sure the vehicle is still properly positioned on the lift. Removal of the stand
can be accomplished by turning the spin handle in a counterclockwise direction until the stand's saddle is clear of the vehicle.
PREVENTATIVE MAINTENANCE
This is the safety alert symbol used for the PREVENTATIVE MAINTENANCE section of this manual to alert you to
potential personal injury hazards. Obey all instructions to avoid possible injury or death.
1.
Always store the stand in a well protected area where it will not be exposed to inclement weather, corrosive vapors, abrasive dust,
or any other harmful elements. The stand must be cleaned of water, snow, sand, grit, oil, grease or other foreign matter before using.
2.
Use a general purpose grease to lubricate the extension screw.
3.
Every stand owner is responsible for keeping the stand labels clean and readable. Use a mild soap solution to wash external
surfaces of the stand. If product labels are lost or not legible, contact an authorized K-Tool International repair center for
replacements.
4.
Inspect the stands before each use. Do not use the stands if any component is cracked, broken or bent. Do not use the stand if
it has loose or missing hardware or components, or is modified in any way. Take corrective action before using the stand again.
Premature wearing or damage to components caused by loose or missing hardware is not eligible for warranty consideration.
KTI-XD61002
3
Rev. 01/14/21
Publicidad
