Congratulations On Your Purchase; Safety Precautions; Preparing For Setup - Sulion UFO BASIC Manual De Instrucciones

Congratulations on your purchase

Congratulations on purchasing the latest energy-efficient
ceiling fan technology. This fan has a direct current (DC)
motor, giving it high energy efficiency and air circulation
volume without added noise.
Energy efficiency: The DC motor is the latest in fan design
technology. It saves up to 70% of energy compared to fans
with traditional alternating current (AC) motors.
Silent operation: This fan's DC motor uses a stabilised
current, which significantly reduces the operating noise.
Low-heating operation: This DC motor is powered
efficiently, reducing its operating temperature to under 50ºC.
This results in better cooling than a standard AC motor and
increases its durability.
Comfort: This fan with a DC motor includes a six-speed
remote control that exceeds the traditional number of speeds
in AC motors, allowing a greater variety of comfort levels.

Safety precautions

The information included on the following pages has been
prepared to ensure that you get the most from your fan:
Carefully follow these instructions to ensure
maximum safety when installing and operating
this equipment.
Any action performed on the appliance's
electrical connection, such as cleaning, must
be carried out after ensuring that the general
power supply is disconnected, by removing
10
OFF OFF
the corresponding fuse or "disarming" the
protective switch to ensure total isolation of
the power supply.
The equipment must be installed by a certified
electrician in accordance with the standards
in force in the country where the installation
takes place. Please remember to require your
installer to test all the fan functions before
leaving. In case of any doubt from the installer,
do not hesitate to contact us.
This device may be used by children aged 8
years and above and persons with reduced
physical, sensory or mental capabilities or
lack of experience or knowledge, if they are
<8 properly supervised or trained in the safe use
of the device and understand the dangers
of its use. Children should not play with the
device. The cleaning and maintenance of the
device should not be carried out by children
without supervision.
The mounting bracket must be attached to a
ceiling structure that is capable of supporting
a minimum of 30 kg. At least 30 mm of the
length of the screws must be screwed into
Kg
the ceiling. If the fan is being installed onto a
ceiling junction box, secure the fan sufficiently
to prevent it from loosening or rotating.
CIF A28763647
The system of attaching the fan bracket to the
ceiling will depend on the type of ceiling where the
installation is to be done. The decision on which
attachment system to use and the quantity is the
installer's responsibility.
The fan must be installed to ensure that the blades
are at least 2.3 m above the ground. Make sure
that there is a space of at least 30 cm between the
fan's blades and any wall or other obstacle with
which they could collide. It is important to note
that the greater the distance, the more efficient
the airflow would be.
The fan's ground wire must be connected to the
installation's earth network to avoid any surges
putting people in danger.
Do not connect the fan's power supply to any
regulating elements or potentiometers, as it could
cause the fan to malfunction and/or will damage
the motor. For the electrical connection, a circuit
breaker must be installed in accordance with the
installation regulations, which ensures a multi-
pole break, is directly connected to the power
terminals and has contact separation in all poles,
which provides total disconnection in accordance
with Category III overvoltage conditions. Only use
the fan's control to turn it on or stop it.
It is recommended to not use these types of fans
with gas installations simultaneously in the same
room.
Do not insert anything that could hit the fan's
blades while it is rotating, as this could cause
damage to people, damage the blades and can
offset the unit, causing vibrations and wobbling.
After installing the fan, ensure that all the fastenings
are secure and tightened in order to avoid any
noise caused by loose elements. Some fastenings
may become loose due to the fan's movement.
Check all fastenings at least twice a year to ensure
that they are tight enough. If necessary, they must
be retightened.
If the power cable is damaged, it must be replaced
by the manufacturer, its after-sales service or
similar certified personnel to avoid any hazard.
Only suitable for indoor.
Replaceable LED
Replaceable driver
Replaceable receiver and remote control
Do not dispose of electrical products with
household waste. Please recycle the packaging
at designated collection points. Contact the local
authorities or your service provider for recycling
advice. Thank you for recycling at the designated
collection points.
+34 916774540 Calle Verano, 51 - Polígono Industrial Las Monjas -28850 Torrejón de Ardoz - Madrid (ESPAÑA)
Note: The important warnings and instructions in this manual are not guaranteed to cover all possible conditions and situations
that may arise. Products do not come with common sense, caution and care. Users must use the fan with due care and caution,
employing common sense, to make good use of the fan.
Device technical spectifications
General
Nominal voltage and frequency
Energy rating
Ingress protection
Work temperature
Maximun ceiling slope on which it can be installed
Weight
Power consumption in standby mode (W)
Service value measurement standard
LED
Power
Light output
Color temperature
RGB
Light data measurement
ON/OFF cycles
Life hours
Dimmable
Angle
CRI
This product have a light source of energy efficiency class
Fan
No. of speeds
Power (W)
RPM
Airflow (m³/min)
Airflow (m³/h)
Max noise level (dB)
Service value SV ((m³ / min) / W)
Maximum air speed (m / sec)

Preparing for setup

Note: The estimated Setup time is 120 minutes. This product
must only be installed by a certified electrician.
Remove the fan from the packaging carefully, avoiding the use
of knives which could scratch any part of it.
Remove all the components. Place the motor on a cloth or soft
surface so as not to damage its surface finish.
Carefully handle the unit to make sure that its casing does not
bend or get scratched.
The fan must be mounted on the floor or a large enough table
to prevent any component from falling off.
ATC: 916749481 - info@sulion.es / SAT : 916749483 - sat@sulion.es
220-240V~AC 50/60Hz
EN 62879:2020
3000 - 6000K
360º Sphere
Instructions for synchronizing the receiver
and the remote control
This fan's remote is synced to the receiver at the factory, so
initially, it does not need to be synced.
Make sure that all connections are correctly set up.
Make sure the remote control has batteries.
Make sure that all switches are switched on (main and isolator
switches).
The control of this fan have two mode of synchronization, Univer-
sal mode and Unit mode:
Clase I
IP20
-5 40ºC
↔
0º
2,9Kg
<0,5
44W
4400lm
No
10000
30000h
Yes
120º
11
>80
E
3
30
1140
93
8520
35
3,1
6,52m/s
www.sulion.es