Publicidad
Idiomas disponibles
Idiomas disponibles
HDMI™ Switch 4 to 1
EN
water and seak medical attention immediately.
• Do not deform, burn or disassemble batteries and never
puncture them with a sharp object.
Extreme heat can lead to explosion and/or leakage of cor-
rosive liquid. Mechanical damage can cause gaseous sub-
stances to escape, which can be highly irritating, flamma-
ble or toxic.
• Do not short-circuit batteries or immerse them in liquids.
There is a risk of explosion, fire, heat, smoke and/or gas
development.
• If the battery is accidentally dropped into water, remo-
ve it immediately. Place the battery in a safe, open area
and stay away until it is completely dry. Do not reuse
the dried battery, but dispose of it as indicated in chap-
ter 8.2.
2 Description and function
2.1 Product
The product is an HDMI™ switcher that can connect up to
4x HDMI™ source devices to 1x HDMI™ output device si-
multaneously. The switcher can be controlled via the switch
button on the unit or the remote control.
2.2 Scope of delivery
HDMI™ Switch 4 to 1 (4K @ 60 Hz), Power supply,
Charging cable, Remote control, 1x Lithium button cell
(CR2025), User Manual
2.3 Operating Elements
See Fig. 1.
1 LED status indicators
2 Switch button
3 Infrared sensor
4 HDMI™ socket (output)
5 HDMI™ socket (input)
6 Micro USB socket
3 Intended use
This product is intended exclusively for private
use and its intended purpose. This product is not
intended for commercial use. We do not permit
using the device in other ways like described in chapter
„Description and Function" or in the „Safety Instructions".
Use the product only in dry interior rooms. Not attending to
these regulations and safety instructions might cause fatal
accidents, injuries, and damages to persons and property.
4 Preparation
1. Check the scope of delivery for completeness and in-
tegrity.
2. Compare the specifications of all used devices and en-
sure compatibility.
5 Connection and operation
5.1 Connection
NOTICE!
• Disconnect the power to the switcher before connecting
or disconnecting your source and output devices via the
HDMI™ sockets.
See Fig. 2.
1. Connect up to four source devices to the HDMI™ so-
ckets (input) (5) of the switcher.
2. Connect an output device to the HDMI™ socket (output)
(4) of the switcher.
Connection cables are not included in the delivery. Make
sure that the source and output devices as well as the
connection cables support the resolutions and standards
of the product!
3. Connect the USB-A plug (9) of the charging cable to the
USB-A socket (8) of the power supply.
4. Plug the Euro plug (7) of the power supply into a free
and easily accessible socket.
5. Connect the micro USB plug (10) of the charging cable
to the micro USB socket (6) of the switcher.
The switcher is now supplied with power.
6. Disconnect all cable connections after use.
REV2022-11-14
Subject to change without notice.
V1.0aw
7 Euro plug
8 USB-A socket
9 USB-A plug
10 Micro USB plug
11 Remote control
Material damage
5.2 Operation
• Press the switch button (2) to swap between the in-
put signals.
5.3 LED status indicators
Designation
Description
The LED lights red when power is sup-
POWER
plied to the switcher.
The LED lights red when the source
INPUT 1,
device connected to the respective
INPUT 2,
HDMI™ socket (input) is properly con-
INPUT 3,
nected.
INPUT 4
The LED lights up green when the re-
spective source device is active.
The LED lights up green when the out-
OUTPUT
put device is correctly connected and
switched on.
6 Remote control
6.1 Activating the remote control
• Pull the contact protector out of the battery compart-
ment.
6.2 Buttons
• Press the IN1, IN2, IN3 or IN 4 button to select the cor-
responding input signal.
• Press the button
nals in order.
6.3 Changing the battery
Replace the dead battery with a new one of the same type
if necessary.
1. Open the battery compartment by pushing the small le-
ver to the side and then pulling out the battery com-
partment.
2. Remove the empty battery.
3. Place the new battery in the battery compartment with
the positive terminal facing upwards.
4. Close the battery compartment again.
5. Dispose of the empty battery properly.
7 Maintenance, Care, Storage and
Transportation
The product is maintenance-free.
NOTICE!
• Always disconnect the mains plug before cleaning.
• Only use a dry and soft cloth for cleaning.
• Do not use detergents or chemicals.
• Store the product out the reach of children and in a dry
and dust-protected ambience when not in use.
• Store cool and dry.
• Keep and use the original packaging for transport.
8 Disposal instructions
8.1 Product
According to the European WEEE directive, electri-
cal and electronic equipment must not be disposed
with consumers waste. Its components must be re-
cycled or disposed apart from each other. Otherwi-
se contaminative and hazardous substances can
damage the health and pollute the environment.
As a consumer, you are committed by law to dispose elect-
rical and electronic devices to the producer, the dealer, or
public collecting points at the end of the devices lifetime for
free. Particulars are regulated in national right. The symbol
on the product, in the user manual, or at the packaging all-
udes to these terms. With this kind of waste separation, ap-
plication, and waste disposal of used devices you achieve
- 5 -
Pillmannstraße 12 | 38112 Braunschweig | Germany
58489
to go through all the input sig-
Material damage
Goobay® by Wentronic GmbH
Publicidad
