Cleaning And Maintenance - cecotec BAMBA TOOTHCARE 1200 JET PRO Manual De Instrucciones

ENGLISH
Pause/Control
You can stop water temporarily at any time by pressing the Pause button on the handle. Fig. 9
When finished, you must turn off the unit by placing the UV/OFF/ON knob in the OFF position
and emptying the remaining liquid in the tank. Unplug the unit.
Periodontal nozzle Fig. 10
The periodontal nozzle releases water and anti-bacterial solution in the periodontal pockets.
It is designed to reach the deepest areas in the periodontal cavity.
To use this nozzle, lean over the sink and place the nozzle carefully under the gumline, in a 45º
angle. Turn on the unit with the lowest pressure setting and clean the gumline by introducing
the nozzle between your teeth. Continue over the gumline until you finish cleaning.
Braces nozzle Fig. 11
The special nozzle for braces is exclusively designed to brush and rinse simultaneously the
areas difficult to access around braces and other dental works.
To use the braces nozzle, lean over the sink and use the bristles to slightly clean around the
braces, water will flow through the brush to rinse.
Tongue cleaner nozzle Fig. 12
Lean over the sink, place this nozzle over your tongue and turn on the unit with the lowest
pressure setting. Increase it if necessary. Place the nozzle on the centre of your tongue and
drag it forward applying slight pressure.
Dental plaque nozzle Fig. 13
Direct the jet in a 90º angle to the gumline, slightly close your lips to avoid splashes, but
allow water to flow freely from your mouth to the sink. Start in the molar area (back teeth)
and continue towards the front teeth, place the nozzle close to your teeth so bristles touch
them softly.
Gently slide the nozzle along the gumline, passing briefly between the teeth to brush them
gently and allow the water to flow between your teeth. Continue until all areas around and
between the teeth have been cleaned, both inside and outside, top and bottom.
Using other solutions
You can use mouthwashes and antibacterial solutions intended for this purpose, paying
special attention when cleaning.
To avoid clogging the irrigator after the use of solutions you should rinse it as follows: fill the
tank partially with warm water and operate the device with the nozzle pointing towards the
sink until the tank is empty.
To finish
Turn off the irrigator and completely empty the liquid left in the tank.
If you use special solutions, clean and rinse thoroughly the tank.
46 BAMBA TOOTHCARE 1200 JET PRO

4. CLEANING AND MAINTENANCE

Cleaning
Before cleaning it, turn off and unplug the irrigator.
After using special solutions in the tank, rinse the unit thoroughly.
After every use, you can use the UV light to sanitise the nozzles as explained above.
Fill half the tank with warm tap water, with the nozzle pointing towards the sink, turn the unit
on and let it run until the tank is empty, this will help prevent the nozzle from clogging and
help your unit last longer.
Clean the product, if necessary, with a soft cloth and a soft non-abrasive cleaning agent.
Disconnect the appliance from the power supply before cleaning.
Maintenance and repair
After cleaning the oral irrigator, place the tank upside down on a flat surface to make sure
it completely dries. When it is completely dry, place it again on the body, also clean and dry.
You must place it in the original box or a similar one when it is not going to be used for a long
time.
If the robot does not work properly, contact the Cecotec Technical Support Service.
Do not try to disassemble or repair the product. If this causes any problems with the product,
the warranty will not cover it.
5. TROUBLESHOOTING
Problem Cause
Leak between the nozzle and The nozzle is not correctly
the handle knob assembled
Periodontal nozzle tear The nozzle is worn
The oral irrigator base hose Damaged hose
handle leaks
The tank leaks The water tank valve is
missing or upside down
Inadequate pressure The tank is not assembled
correctly.
The nozzle is clogged
The unit does not release The motor is not working
water
ENGLISH
Solution
Remove the nozzle and try
placing it back again until it
clicks
Replace it with a new nozzle
Contact the official Technical
Support Service of Cecotec to
replace it
Replace the tank valve
Turn the valve
Make sure the tank is full of
water and correctly placed
Clean the nozzle following
the instructions
Make sure the power supply
works, check it with another
device (check the circuit
breaker and/or wall switch)
BAMBA TOOTHCARE 1200 JET PRO 47