König SAS-ALARM240 Manual De Usuario página 4

Settings and queries
The settings and queries can be carried out using the remote control or the control panel.
Settings
• To enter the setting mode, press the setup button on the control panel.
• To change the settings, press [#] + [code] + parameters + [#].
• To exit the setting mode, press [*] + [#].
Setting Command
Record voice message [#] + [19] + message + [#]
Add remote control [#] + [07] + [xxx] + [#]
Delete remote control [#] + [08] + [xxx] + [#]
Delete all remote controls [#] + [08] + [***] + [#]
Add detector [#] + [09] + [xxx] + [#]
Delete detector [#] + [10] + [xxx] + [#]
Delete all detectors [#] + [10] + [***] + [#]
Set up phone number(s) [#] + [3] + [y] + phone number + [*#]
Delete phone number(s) [#] + [3] + [y] + [#]
Setup password [#] + [50] + password + [#]
Setup arming delay time [#] + [51] + seconds + [#]
Setup alarm delay time [#] + [52] + seconds + [#]
Setup siren time [#] + [53] + minutes + [#]
[#] + [56] + year + month + day +
Setup date and time
hour + minutes + seconds + [#]
[#] + [57] + [yy] + start time + end
Setup alarm clock
time + day(s) + [#]
Delete alarm clock [#] + [57] + [yy] + [0] + [#]
Setup remote control by
[#] + [62] + [y] + [#]
telephone
Setup number of rings for
[#] + [18] + [yy] + [#]
remote control by telephone
Setup audible feedback [#] + [11] + [y] + [#]
Volume audible feedback [#] + [79] + [y] + [#]
Display brightness control [#] + [83] + [y] + [#]
Set up power-saving mode [#] + [84] + [y] + [#]
Volume built-in siren [#] + [87] + [y] + [#]
Setup display light flashing [#] + [88] + [y] + [#]
Setup telephone line connection
[#] + [13] + [y] + [#]
detection
Disable use of remote control for
[#] + [15] + [y] + [#]
arming/disarming
Setup interference prompts [#] + [16] + [y] + [#]
Setup control panel lock [#] + [17] + [y] + [#]
Press the "SET" button on the strobe
siren to enter start code learning.
Add wireless strobe siren Press the disarm button on the
(option) control panel. The strobe siren beeps
once to indicate that the learning
process is completed successfully.
Volume external siren
[#] + [14] + [yy] + [#]
(option)
Restore factory settings for
[#] + [9898] + [#]
control panel
System reset [#] + [989801] + [#]+ [#]+ [#]
Remarks
Voice message duration: max. 10 seconds.
[xxx] = remote control ID (001-120). After adding, press a button on the remote control.
2 beeps = remote control added succesfully. 1 beep = remote control already configured.
Max. number of remote controls: 120.
[xxx] = value of remote control to be removed.
[***] = all connected remote controls.
[xxx] = detector ID (001-120). Max. number of detectors: 120.
[xxx] = value of detector to be removed.
[***] = all connected detectors.
[y] = phone number ID (1-9).
ID 1-6 = regular phone numbers. ID 7-9 = emergency phone numbers.
[y] = phone number ID (1-9).
The password has a maximum of 4 digits. Default password: 1234.
Seconds from 00 to 99. Default = 00.
Seconds from 00 to 99. Default = 60.
Minutes from 00 to 20. Default = 01.
Example: "20141025183500" = October 25, 2014 18:35:00.
[yy] = 05 / 06 (max. 2 alarms).
Example 1: "050900090112345" = siren sounds for 1 minute on weekdays at 09.00.
Example 2: "051030103167" = siren sounds for 1 minute during weekends at 10:30.
[yy] = 05 / 06.
[y] = 0 (off ) or 1 (on). Default = 1 (on).
[yy] = 00 (off ) - 99. Default = 8.
[y] = 0 (off ) or 1 (on). Default = 1 (on).
[y] = 0 (off ) - 7 (loud).
[y] = 0 (dark) - 7 (bright).
[y] = 0 (off ) or 1 (on). Default = 1 (on).
[y] = 0 (off ) - 7 (loud).
[y] = 0 (off ) or 1 (on). Default = 0 (off ).
[y] = 0 (off ) or 1 (on). Default = 0 (off ).
[y] = 0 (off ) or 1 (on). Default = 0 (off ).
If other devices try to connect to the alarm system, the siren will sound for 5 seconds.
[y] = 0 (off ) or 1 (on). Default = 0 (off ).
[y] = 0 (off ) or 1 (on). Default = 0 (off ).
Contact your local reseller for availability.
[yy] = 00 (off ) - 99 (loud).
Caution: The entire alarm system is restored to the factory settings.
4 4
English