Safety Warnings; Installation Instructions; Use And Maintenance - Refsta 3LIP0156 Manual Del Usuario

GENERAL
Carefully read the contents of this leaflet since it provides
important instructions regarding safety of installation, use
and maintenance. Keep the leaflet for possible future
consultation. All the operations relating to installation
(electrical connections) must be carried out by special-
ised personnel in conformity with the regulations in force.

SAFETY WARNINGS

It is recommended to use flat-bottom pans with a diam-
eter equal to or slightly larger than that of the heated area.
Do not use pans with a rough base to prevent scratching
the heat surface of the cooktop (Fig.2).
This appliance is not suitable for use by children or per-
sons requiring supervision. Do not let children play with
the appliance.
IMPORTANT
- Avoid spilling liquid, therefore to boil or heat liquids,
reduce the heat.
- Do not leave the heating elements on with empty pots
and pans or without receptacles.
- When you have finished cooking, switch off the relevant
heating element with the control indicated below.
ATTENTION:
- Steam cleaners must not be used.
- If the surface is cracked, switch off the appliance to
prevent electric shock.
- This appliance is not intended for use by young
children or infirm persons without supervision
- Young children should be supervised to ensure they
do not play with the appliance
This appliance conforms to the European Directive EC/
2002/96, Waste Electrical and Electronic Equipment
(WEEE). By making sure that this appliance is disposed
of in a suitable manner, the user is helping to prevent
potential damage to the environment or to public health.
The symbol on the product or on the accompanying
paperwork indicates that the appliance should not be
treated as domestic waste, but should be delivered to a
suitable electric and electronic appliance recycling collec-
tion point. Follow local guidelines when disposing of waste.
For more information on the treatment, re-use and
recycling of this product, please contact your local author-
ity, domestic waste collection service or the shop where
the appliance was purchased.

INSTALLATION INSTRUCTIONS

These instructions address specialised installers and serve
as a guide for installation, adjustment and maintenance
in conformity with the laws and regulations in force.
If a built-in oven or any other appliance that generates
heat must be fitted directly under the glass-ceramic
cooktop, THIS APPLIANCE (oven) AND THE GLASS-
CERAMIC COOKTOP MUST BE SUITABLY INSULATED
in such a way that the heat generated by the oven, meas-
ured on the bottom right of the cooktop, does not exceed
60°C. Failure to respect this precaution may determine
ENGLISH
improper functioning of the TOUCHCONTROL system.
POSITIONING (Fig.1)
The domestic appliance is designed to be built into a
worktop as illustrated in the specific figure. Apply sealant
around the entire perimeter (cut-out dimensions Fig.1B).
Fix the domestic appliance on the worktop by means of
the 4 brackets provided, taking the thickness of the worktop
into account (Fig.1A). If the lower part of the appliance,
after installation, is accessible via the lower part of the
cabinet then it is necessary to mount a separator panel
respecting the distances indicated (Fig.1C). If the
appliance is installed with an oven underneath then the
separator is not necessary.
ELECTRICAL CONNECTIONS
Before making the electrical connections, check that:
- the ground cable is 2 cm longer than the other cables;
- the system ratings meet the ratings indicated on the
identification plate fixed on the lower part of the worktop;
- the system is fitted with efficient earthing compliant to
the laws and regulations in force.
Earthing is obligatory by law.
If the appliance is not fitted with a cable, use type:
"H05V2V2-F" for a power level of up to 6400 Watts. The
cross-section of the cable should be at least 2.5 mm², or 4
mm² for greater power levels.
The cable should never reach a temperature which is 50°C
above the temperature of the room in which it is installed.
The appliance is designed for permanent connection to
the electricity supply and should therefore be fitted with
an omnipolar switch which has a minimum opening of 3
mm between contacts. The switch should be suitable for
the charge indicated on the appliance data plate and must
conform to all current legislation (the yellow/green earth
wire must not be interrupted by the switch).
The omnipolar switch must be easy to reach once the
installation process has been completed.

USE AND MAINTENANCE

MAINTENANCE
Remove any residues of food and drops of grease from
the cooking surface using the special scraper supplied on
request (Fig.3). Clean the heated area as thoroughly as
possible using SIDOL, STAHLFIX or similar products and
a cloth/paper, then rinse with water and dry with a clean
cloth. Using the special scraper (optional) immediately re-
move any fragments of aluminium and plastic material that
have unintentionally melted on the heated cooking area
or residues of sugar or food with a high sugar content
(Fig.3). In this way, any damage to the cooktop surface is
prevented.
Under no circumstances use abrasive sponges or irritat-
ing chemical detergents such as oven sprays or stain
removers.
USE
Use the touch control system in the corresponding posi-
tion relative to the individual cooking needs. Keep in mind
that the higher the number, the more heat that it is pro-
duced.
Operation (fig.5)
A = ON/OFF button
B1 = ON/OFF button hotplate 1
- 13 -
GB