Eaton PLLA M2 Información De Instalación Y Mantenimiento

Champ® Linear LED
PLLA M2 Linear LED Luminaire Fittings
Installation & Maintenance Information
APPLICATION
Linear LED luminaires are suitable for use in the following locations as defined by
the National Electrical Code (NEC®):
Products are marked for Marine use and must be installed in accordance with
CG-259 Coast Guard requirements, where applicable.
The assembled luminaire shall be installed in accordance with the National Elec-
tric Code NFPA70, and American Bureau of Shipping.
NEC
• Wet location, IP66/67 , Type 4X
These luminaire housings shall be used with UL listed Crouse-Hinds ordinary
locations luminaire fittings namely LED Light Engine Cat. Nos. PLLA*2 or
PLLA*4 series ending with M2 and hazardous locations Mounting means Cat.
Nos. M2-FLUSH-MT-KIT, M2-CEILING-SWIVEL -KIT, M2-CEILING-WALL -KIT, M2-
PM-KIT-1.25, M2-PM-KIT-1.5, M2-PM-KIT-2.0, (refer to label provided inside the
driver housing for permissible fitting details).
!
To avoid the risk of fire, explosion or electric shock, this product should
be installed, inspected and maintained by a qualified electrician only, in
accordance with all applicable electrical codes.
!
To avoid electric shock, be certain electrical power is OFF before and during
installation and maintenance. Luminaire must be supplied by a wiring
system suitable per NEC with an equipment grounding conductor. To
avoid burning hands, make sure lens and lamp are cool when performing
maintenance.
!
To avoid explosion, make sure the supply voltage is the same as the
luminaire voltage.
Do not install where the marked operating temperatures exceed the ignition
temperature of the hazardous atmosphere.
Do not operate in ambient temperatures above those indicated on the
luminaire nameplate.
Use only replacement parts from Eaton's Crouse-Hinds.
Contact Eaton's Crouse-Hinds for information on product repair.
Use proper supply wiring as specified on the luminaire nameplate.
All gasket seals must be clean.
Before opening, electrical power to the luminaire must be turned off. Keep
tightly closed when in operation.
IF 1938 • 04/22
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
WARNING
WARNING
8 7
NOTES:
1.
WARNING D
175.3
6.90
C
123.2
4.85
B
A
8 7
Copyright © 2022, Eaton's Crouse-Hinds Division
UL Standards:
• UL1598 Luminaires, UL1598A Marine
• UL8750 LED Equipment for Lighting Products
CSA Standard:
• CSA C22.2 No. 250
Refer to the luminaire fitting nameplate for specific classification information,
maximum ambient temperature suitability, and electrical specifications. The
assembled Linear LED luminaire is designed for use indoors and outdoors in
marine and wet locations, where moisture, dirt, corrosion, vibration and rough
usage may be present.
INPUT VOLTAGE:
• UNV1: 120-277 VAC 50/60 Hz and 127/250 VDC
• UNV34: 347-480 VAC 50/60 Hz
INSTALLATION
A. M2-FLUSH-MT-KIT
1. Make sure the power is disconnected to the conduit system before
installing the luminaire.
2. Install flush mount brackets to rear of luminaire driver housing using
the provided two (2) 1/4" hex bolts and split ring lock washers for each
bracket. Bracket orientation as shown in Figure 1. Torque to 64 in.-lbs (7 .2
N-m).
3. Identify mounting location suitable for supporting luminaire, mark and drill
holes for flush brackets per dimensions shown in Figure 1.
4. Luminaire is now ready for mounting. It is strongly suggested to use
two (2) qualified tradespeople to proceed with the final mounting of the
luminaire. This is recommended to avoid any personal injury or damage to
the luminaire.
Do not let the luminaire hang or flex on one bracket at a time. Failing to
comply will result in breakage of bracket and possible injury or death.
5. Install and tighten four (4) 1/4" diameter fasteners (customer supplied) in
bracket mounting holes. It is recommended that stainless steel hardware
be used in locations with corrosion concerns.
5
6 4
2 Foot
Length
(in)
A 24.0
B
B 24.25
C 2.50
A
8
NOTES:
1.
1/4-20 x 1/2" HEX HEAD BOLT
660
D
26.0
1/2" SPLIT LOCK WASHER
A
175.3
6.90
C
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND
123.2 TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION.
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN
4.85
MATERIAL:
FINISH:
6 5 4
B
Figure 1. Flush Ceiling Mount Installation
A
8
!
WARNING
3 2 1
ZONE NO. DESCRIPTION DATE APPRD. LTR. NO.
2 Foot 4 Foot 4 Foot
C D
(mm) (in) (mm)
610 39.0 991
616 24.25 616
63.5 2.50 63.5
C
5
7 6
B
A
TOLERANCES UNLESS OTHERWISE SPECIFIED,
UNLESS OTHERWISE SPECIFIED ALL PRIMARY DIMENSIONS
in. mm ARE IN INCHES.
.X ± .1 ± .3
DIMENSIONS IN [ ] ARE IN
.XX ± .01 ± .13
AND IS TO BE RETURNED UPON REQUEST. MILLIMETERS.
.XXX ± .005 ± .000 Title Line 1
Material ORIGINAL DATE MM/DD/YYYY
ANGLES ± 1.5 ± 1.5 TITLE
... THICK
DIM AND TOL IN ACCORDANCE REDRAWN DATE MM/DD/YYYY Title Line 2
Finish WITH ASME Y14.5 2009. Your Name
DRAWN BY
CODE ... THIRD ANGLE PROJECTION CHECKED BY Your Name FIRST MADE FOR Catalog Family
ASSY2 CAT2 APPROVED BY Your Name SIZE CODE IDENT. NO. 0000000 REV.
D
ASSY1 CAT1 Your name rev
APPROVED BY
NEXT ASSY. USED ON
APPLICATION SCALE 1:2 WT. 15.84 LB SHEET 1 OF 5
3 2 1
660
26.0
A
7 5
6
IF 1938
4 3 2
ZONE NO. DESCRIP
C
B
A
1/4-20 x 1/2" HEX HEAD BOLT
1/2" SPLIT LOCK WASHER
TOLERANCES
THIS IS PROPERTY OF EATON AND CONTAINS CONFIDENTIAL AND UNLESS OTHERWISE SPECIFIED,
TRADE SECRET INFORMATION. POSSESSION DOES NOT CONVEY UNLESS OTHERWISE SPECIFIED
ANY RIGHTS TO LOAN, SELL OR DISCLOSE SAID INFORMATION. ALL PRIMARY DIMENSIONS
in. mm
REPRODUCTION OR USE FOR ANY PURPOSE OTHER THAN WHICH ARE IN INCHES.
IT WAS SUPPLIED MAY NOT BE MADE WITHOUT EXPRESS .X ± .1 ± .3
DIMENSIONS IN [ ] ARE IN
WRITTEN PERMISSION OF EATON. THIS DRAWING IS ON LOAN .XX ± ±
AND IS TO BE RETURNED UPON REQUEST. .01 .13 MILLIMETERS.
.XXX
± .005 ± .000
MATERIAL: Material Page 1 ANGLES ORIGINAL DATE MM/DD/YYYY
± 1.5 ± 1.5 TITLE
... THICK
REDRAWN DATE MM/DD/YYYY
DIM AND TOL IN ACCORDANCE
FINISH: Finish WITH ASME Y14.5 2009. DRAWN BY Your Name
CODE ... FIRST MA
THIRD ANGLE PROJECTION CHECKED BY Your Name
ASSY2 CAT2 APPROVED BY Your Name SIZE
D
ASSY1 CAT1 APPROVED BY Your name
NEXT ASSY. USED ON
SCALE 1
APPLICATION
4 3 2