Publicidad
Idiomas disponibles
Idiomas disponibles
3. ASSEMBLY
Inserting / replacing the batteries (Fig. B)
The water timer is powered by 2 x 1.5V AA Alkaline
batteries (not included).
1. Remove the battery compartment cover(6) on
the backside of the timer.
2. Insert batteries with correct polarity according
to battery compartment indications
3. Ensure a good closure of the cover by pushing it
firmly against the housing.
In order to stop the device from failing because of
a weak battery the battery must be replaced when
the low battery symbol indicator appears.
4. OPERATION
• The water pressure used must not exceed 8bar
/ 0.8MPa to avoid damage to this product.
• The digital timer may only be positioned vertical-
ly with the hose coupling (4) downwards to pre-
vent water entering the battery compartment(6).
Installing the water timer (Fig. A)
1. Connect the water timer to the tap. The union
nut (1) will fit a water tap with G 3/4" (26.5mm)
thread. For a tap with G 1/2" (21mm) thread use
the adapter (2).
2. Connect the hose coupling(4) to a water hose
connection.
Programming the water timer (Fig. C)
1. Set the current time, NOW by pressing
hour will flash on display. Set the time in hours
with
&
. Confirm with
flash on display. Set the time in minutes with
&
. Confirm with
. The water timer will au-
tomatically enter to the next step for the starting
time of a watering program, START TIME.
2. Set START TIME. The hour will flash on display.
Set the start time in hours and minutes with
&
and confirm with
automatically enter to the next step for setting
the duration of a watering program, HOW LONG.
3. Set HOW LONG. The digit will flash on display. Set
the duration in minutes or seconds with
and confirm with
. The water timer will auto-
matically enter to the next step for setting the
frequency of a watering program, HOW OFTEN.
WWW.VONROC.COM
4. Set HOW OFTEN. The digit will flash on display.
5. The water timer displays the remaining time till
In addition to setting up a watering program, the
water timer has the following features.
Manual watering
This feature allows you to water without interrupting
the set watering program. You can start the water
flow manually and set it for a period between 1 se-
cond and 99 minutes. To set this press
duration in minutes or seconds with
confirm with
countdown and the
To manually stop the watering function press
Delay watering
The delay function makes it possible to postpone
the next watering cycle and then auto resume the
set program. Hold
will be displayed and the next start will be updated.
To remove the set delay hold
Off mode
During the OFF mode the actual watering and
programmed schedules will not be executed. The
set program will be saved and resumed after the
OFF mode has been switched off. To switch off the
digital timer press
time, battery indicator and OFF will be displayed. To
reactivate the device press
Child lock
. The
To prevent unwanted settings, the device can be
locked by pressing
. The minute will
symbol is shown in the display. To unlock the device
press
General functions
• If a set schedule intersects with manual wate-
. The water timer will
• You can stop the waterflow at any time, either
• When you enter to the setting interface uninten-
&
Set the frequency in days or hours with
and confirm with
.
next watering cycle by NEXT START.
. The timer starts the watering. The
icon is shown on the display.
for 3 seconds. The delay icon
for 3 seconds. The current
+
for 3 seconds. A lock
+
again for 3 seconds.
ring, the set cycle will be cancelled. The next
cycle will be executed.
an active schedule or manual watering. To do
this press
.
tionally, but do not want to change the timing
program plan, you have two options. Keep
pressing
until you return to the main screen
or press
and return to the main screen.
EN
&
. Set the
&
and
.
for 3 seconds.
for 3 seconds.
5
Publicidad
