Sears Kenmore 110.3316 Serie Manual De Uso Y Cuidado página 17

First try the solutions suggested here for assistance and to possibly avoid a service call.
If you experience
Washer not performing as expected (cont.)
Washer not draining/
spinning, loads are
still wet (cont.)
Incorrect or wrong wash or
rinse temperatures
Load not rinsed
Sand, pet hair, lint, etc. on
load after washing
Load is tangling
Not cleaning or
removing stains
TROUBLESHOOTING
Possible Causes
Washer may be tightly packed or
unbalanced.
Load off balanced.
Check plumbing for correct drain hose
installation. Drain hose extends into
standpipe farther than 4.5" (114 mm).
Not using HE detergent, using too much
HE detergent.
Check for proper water supply.
Energy-saving controlled wash
temperatures.
Check for proper water supply.
Not using HE detergent, using too much
HE detergent, or using.
Washer may be tightly packed.
Heavy sand, pet hair, lint, and detergent
or bleach residues may require
additional rinsing.
Washer not loaded as recommended.
Wash action and/or spin speed too fast
for load.
Wash load not completely covered
in water.
Added more water to washer.
Washer not loaded as recommended.
Tightly packed loads may not allow the washer to spin correctly, leaving
the load wetter than normal. Evenly arrange the wet load for balanced
spinning. Select RINSE & SPIN to remove excess water. See "Using Your
Washer" for loading recommendations.
See "Vibration or Off-Balance" in Troubleshooting section for more
information.
Check drain hose for proper installation. Use drain hose form and
securely attach to drainpipe or tub. Do not tape over drain opening.
Lower drain hose if the end is higher than 96" (2.4 m) above the floor.
Remove any clogs from drain hose.
Suds from regular or too much detergent can slow/stop draining or
spinning. Use only HE detergent. Always measure and follow directions
for your load. To remove extra suds, Select RINSE & SPIN.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached to both washer and faucet, and have both
hot and cold water flowing to inlet valve.
Check that inlet valve screens are not clogged.
Remove any kinks in hoses.
ENERGY STAR ® qualified washers use cooler wash and rinse water
temperatures than traditional top-load washers. This includes cooler hot
and warm washes.
Make sure hot and cold inlet hoses are not reversed.
Both hoses must be attached and have water flowing to the inlet valve.
Both hot and cold water faucets must be on.
Inlet valve screens on washer may be clogged.
Remove any kinks in the inlet hose.
The suds from regular detergent can cause the washer to
operate incorrectly.
Use only HE detergent. Be sure to measure correctly.
Always measure detergent and follow detergent directions based on load
size and soil level.
The washer is less efficient at rinsing when load is tightly packed.
Load items in loose heaps evenly around the washplate.
Use cycle designed for the fabrics being washed.
Add only 1 or 2 additional items after washer has started.
Add an Extra Rinse to the selected cycle.
Load items in loose heaps evenly around the washplate.
Reduce tangling by mixing types of load items. Use the recommended
cycle for the type of items being washed.
Select a cycle with a slower wash action and slower spin speed. Note that
items will be wetter than when using a higher speed spin.
Washer senses load size and adds correct amount of water. This is normal
and necessary for clothes to move.
Do not add more water to washer. Adding water lifts the items off the
washplate, resulting in less effective cleaning.
Load items in loose heaps evenly around the washplate.
Add only 1 or 2 additional items after washer has started.
Solution
17