Publicidad
Idiomas disponibles
Idiomas disponibles
English
Moving the Pressure Washer (Fig. A)
1. Turn OFF the pressure washer unit
OFF switch
2
to the OFF position. Then turn OFF the
water supply.
2. Point the spray wand
trigger
8
to release remaining water pressure.
3. When the spray wand is completely empty, lift the
pressure washer by the frame handle
Shutdown (Fig. A)
1. Turn OFF the pressure washer unit
OFF switch
to the OFF position. Then turn OFF the
2
water supply and unplug the cord from the outlet.
2. Discharge residual pressure by squeezing the trigger
until no more water comes out of the spray wand
3. Engage the spray trigger lock‑off
4. Disconnect the garden hose from the water intake
5. Disconnect the high pressure hose
pressure water outlet
Soap Tank (Fig. F)
This pressure washer has a built‑in soap tank
1. To fill the soap tank
23
turn off the water supply.
2. Pull trigger on spray handle grip
water pressure.
3. Remove soap tank cap
with appropriate detergent following the detergent
manufacture's instructions.
4. Fit and tighten soap tank cap
soap tank
23
.
5. Attach the soap nozzle
dispense soap.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and disconnect it from
power source before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Your CRAFTSMAN power tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk
of eye injury, always wear ANSI Z87.1 approved eye
protection when performing this procedure.
WARNING: Never use solvents or other harsh
chemicals for cleaning the non‑metallic parts of the
tool. These chemicals may weaken the plastic materials
used in these parts. Use a cloth dampened only with
water and mild soap. Never let any liquid get inside the
tool; never immerse any part of the tool into a liquid.
10
9
by rotating the ON/
3
in a safe direction and pull the
1
.
9
by rotating the ON/
.
7
from the high
13
12
and drain hose.
23
.
, turn off the pressure washer and
6
to relieve any
and fill the soap tank
24
24
back onto the
to the spray wand
21
3
Nozzle Cleaning (Fig. A, M)
If the nozzle becomes clogged with foreign materials, such as
dirt, excessive pressure may develop. If the nozzle becomes
partially clogged or restricted, the pump pressure will pulsate.
Clean the nozzle immediately using the nozzle cleaner.
1. Turn OFF and unplug the pressure washer unit
2. Turn OFF the water supply.
3. Pull trigger
water pressure.
4. Remove the nozzle from the spray wand
the quick connect collar
5. Using the nozzle cleaning tool
from the nozzle.
8
6. Run water from a faucet or garden hose through
.
3
the nozzle.
.
11
Soap Tank Cleaning (Fig. A, F)
To clean the soap tank, decouple the hose from the pump.
1. Turn OFF and unplug the pressure washer unit
2. Turn OFF the water supply.
3. Pull trigger on spray handle grip
water pressure.
4. Decouple the soap hose
port
27
5. Empty any remaining detergent back into its own bottle.
6. Use water from a garden hose to thoroughly rinse out the
23
soap tank
7. Empty the soap tank
8. Reinstall soap tank
tank
23
to
Storage (Fig. N–P)
•
Store in a dry, covered location above freezing
temperature. sTORE inDOORs.
•
Always completetely empty water from high pressure
hose, pressure washer unit, nozzles, and spray wand.
•
The spray handle
handle storage hook
shown in Fig. N.
•
Nozzles can be stored on the crossmember
shown in Fig. O.
•
The power cord
power cord storage hook
•
The high pressure hose
secured to the high pressure hose storage hook
shown in Fig. P.
Accessories
WARNING: Since accessories, other than those offered by
CRAFTSMAN, have not been tested with this product, use
of such accessories with this tool could be hazardous. To
reduce the risk of injury, use only CRAFTSMAN accessories
recommended for this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact CRAFTSMAN call 1‑888‑331‑4569.
on spray handle
8
5
toward the spray wand.
4
22
6
26
from the soap intake
.
23
.
and allow it to fully dry.
23
23
to frame and ensure the soap
is fully secured to the frame pegs
can be attached to the spray
5
on the crossmember
14
28
can be stored coiled up on the
as shown in Fig. P.
15
13
can be stored coiled up and
9
.
to relieve any
3
by pulling
, unclog any debris
9
.
to relieve any
43
.
as
38
as
38
16
as
Publicidad
