Publicidad
Safety warnings for
polishers
• This power tool is intended to function as a polishing
tool. Read all safety warnings, instructions, illustrations, and
specifications provided with this tool.
Failure to follow the instructions below may result in
electric shock, fire and/or serious injury.
• Never have the car running when using the polisher in an
enclosed place.
• Before starting the polishing job, make a test. In the
event the tool makes strange sounds or vibrates in an
unusual way, please turn it off. Disconnect it and take it to
a
Authorized Service Center.
• It is not recommended to perform the operations such as
grinding, sanding, brushing or cutting to be done with this
tool. Operations for which this power tool was not
designed may result in an accident and cause personal
injury.
• When not in service the tool shall be turned off and
disconnected.
• Prevent unexpected starting. Keep your fingers away
from the On /Off switch when connecting the tool into the
power outlet.
• To prevent electric shock, keep the tool dry
and clean, free of any oil or grease residue.
CAUTION
• The assigned speed of the attachment
must be at least equal to the speed marked on the power
tool.
Accessories that operate faster than their assigned speed
may break or come off.
The outside diameter and thickness of the fittings must be
within the rated capacity of the tool.
Incorrectly sized fittings cannot be properly protected or
controlled.
• Keep the power cable away from the tool trajectory while
polishing. Otherwise the disc can trap and cut the cable
exposing the user to electric shock.
• Do not force the tool. Hold it firmly by both handles. Do
not use force downwards, otherwise the tool movement
will slow down, reducing quality in the job and severely
damaging the tool.
• Take good care of the tool. The job is easier if it is in
good conditions.
• Never release the tool until the
CAUTION
attachment comes to a complete stop.
The rotary attachment may catch on a surface and knock
the power tool out of control.
Do not operate the power tool while carrying it beside you.
Accidental contact with the rotary attachment may catch on
clothing, pulling the attachment toward your body.
Clean the power tool's vents regularly.
The motor fan directs dust into the housing, and excessive
accumulation of metal dust can result in an electrical
hazard.
• Do not use accessories which are not specifically
designed and recommended by the tool manufacturer. The
fact that an accessory item may fit the power tool is not an
assurance of safe operation.
• Do not attach a woodworking saw blade or serrated
blade. Such blades create frequent kickback and loss of
control.
CAUTION
• Do not use accessories that require
liquid coolants. Using water or other liquid coolants may
result in electrocution or shock.
• Do not allow any loose portion of the
CAUTION
polishing bonnet or its attachment strings to spin freely.
Tuck away or trim any loose attachment strings. Loose
and spinning attachment strings can entangle your fingers
or snag on the workpiece.
WARNING
• Wear safety glasses.
• Use personal protective equipment. Depending on the
application, use face shield, safety glasses. As appropriate,
use a dust mask, hearing protection, gloves and workshop
apron capable of stopping small abrasive fragments or
pieces of work.
Eye protection must stop the waste generated by the
various operations. Dust masks or respirators must filter
out the particles produced by the operation. Prolonged
exposure to high intensity noise can cause hearing loss.
Keep people present at a safe distance from the work area
Anyone entering the work area should wear personal
protective equipment.
Work piece fragments or a broken attachment can
become detached and cause damage beyond the
immediate area of operation.
Kickback and related warnings
Kickback is the result of power tool misuse and/or
incorrect operating procedures or conditions and can be
avoided by taking proper precautions as given below.
• Maintain a firm grip on the power tool and position your
body and arm to allow you to resist kickback forces.
Always use D-Handle, if provided, for maximum
control over kickback or torque reaction during start-up.
The operator can control torque reactions or kickback
forces, if proper precautions are taken.
• Put the power cord away from the rotating accessory. If
control of the power tool is lost, the cord may be cut or
entangled and the operator's arm or hand may be pulled
into the rotating accessory.
• Do not use the power tool near flammable materials.
Sparks can ignite these materials
• Do not position your body in the area where power tool
will move if kickback occurs. Kickback will propel the tool
in direction opposite to the wheel's movement at the
point of snagging.
• Use special care when working corners, sharp edges etc.
Avoid bouncing and snagging the accessory. Corners,
sharp edges and bouncing have a tendency to snag the
rotating accessory and cause loss of control or kickback.
• Never place your hand near the rotating
attachment.
The accessories may kick back in your hand.
5
ENGLISH
Publicidad
