Publicidad
Idiomas disponibles
Idiomas disponibles
ASSEMBLY INSTRUCTIONS
10. Insert the drawer into the assembly by pressing down
the release levers on the slide runners and sliding the
drawer into the tracks of slides.
11. Locate and mark wooden studs where the unit is to be
installed. Drill a 1/8" pilot hole on the wooden stud
approximately 3" below the height of unit top. Attach one
bracket (a) securely with screw (c) into the pilot hole on
the wall. Attach the other bracket (a) with screw (d) to the
back edge of unit top in line with the bracket (a) on the wall.
Adjust floor levelers to level the unit against the wall where
desired. Put the male end of the steel cable (b) through
each bracket (a). Securely connect both ends together by
turning the female connector clockwise.
Hardware Used
MM
Tipping Restraint Hardware
CARE AND MAINTENANCE
• Use a soft, clean cloth that will not scratch the surface when dusting.
• Use of furniture polishes is not necessary. Should you choose to use polishes, test first in an
inconspicuous area.
• Using solvents of any kind on your furniture may damage the finish.
• Never use water to clean your furniture as it may cause damage to the finish.
• Always use coasters under beverage glasses and flowerpots.
• Liquid spills should be removed immediately. Using a soft clean cloth, blot the spill gently. Avoid
rubbing.
• Always use protective pads under hot dishes and plates. Heat can cause chemical changes that
may create spotting within the furniture finish.
• Stains or marks from crayons or ink markers will be difficult to remove.
• In the event that your furniture is stained or otherwise damaged during use, we recommend that
you call a professional to repair your furniture.
• Check bolts/nuts periodically and tighten them if necessary.
• Touch-up Pen (GG) has been provided to repair any small nicks or scratches that may occur
during assembly or shipping.
10
Wooden Stud
11
b
Wall
b
a
x1
9
LIMITED LIFETIME WARRANTY
This product is warranted to the original purchaser. If there is a failure in this unit due to defects
in materials or workmanship, the manufacturer will repair or replace this item at our discretion
without charge. Warranty is void if product has been assembled incorrectly, misused, abused by
overloading, altered in any way or damaged due to accident. This warranty is not transferable and
does not cover chipping, flaking, scratches, rust, dents, or other damages to the surfaces of this
product. Responsibility of the manufacturer is limited to repair or replacement of this product. The
manufacturer is not responsible for consequential, incidental, or other damages or losses resulting
from product failure.
This warranty is in lieu of all other expressed warranties. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so the above limitation may not apply to you. This
warranty gives you specific legal rights and you may have other rights which vary from state to state.
REPLACEMENT PARTS LIST
For replacement parts, call our customer service department at 1-866-439-9800, 8 a.m. - 8 p.m., EST,
Monday - Sunday. You could also contact us at partsplus@lowes.com or visit www.lowespartsplus.
com.
PART
A
Left Side Frame
B
Right Side Frame
C
Left Side Panel
D
Right Side Panel
d
a
E
Top Panel
F
Bottom Panel
c
G
Back Panel
H
Panel Shelf
I
Metal Bar
J
Drawer Front
K
Drawer Left
L
Drawer Right
M
Drawer Back
N
Drawer Bottom
O
Drawer Stretcher
AA
Cam Bolt
BB
Large Cam Lock
CC
Wood Dowel
DD
M4 x 32mm Screw
EE
1/4" x 10mm Bolt
FF
Nut
GG
Touch-up Pen
HH
Small Cam Lock
II
Handle
JJ
5/32" x 12mm Bolt
KK
Allen Wrench
LL
Open Wrench
DESCRIPTION
PART #
00LWS3FS-01
00LWS3FS-02
00LWS3FS-03
00LWS3FS-04
00LWS3FS-05
00LWS3FS-06
00LWS3FS-07
00LWS3FS-08
00LWS3FS-09
00LWS3FS-10
00LWS3FS-11
00LWS3FS-12
00LWS3FS-13
00LWS3FS-14
00LWS3FS-15
00LWS3FS-16
00LWS3FS-17
00LWS3FS-18
00LWS3FS-19
00LWS3FS-20
00LWS3FS-21
00LWS3FS-22
00LWS3FS-23
00LWS3FS-24
00LWS3FS-25
00LWS3FS-26
00LWS3FS-27
10
C
A
B
D
E
F
G
H
J
I
L
K
Publicidad
