Descargar Imprimir esta página

camry Premium CR 4415 Manual De Uso página 5

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 15
(Do not open the lid (A) until the Moka maker if finished brewing. You might get burned with hot steam and hot coffee.)
15. Once the bottom tank (C ) is empty turn off the device with the On / OFF switch (F). (You will know it is empty as the coffee will not
flow anymore and the noise the device is making will be much lower.)
WARNING Please turn off the device with the ON / OFF switch (F) after each use.
16. Grab the device by the handle and pour the coffee into prepared cups.
Cleaning:
1. Check if the device hot from previous use. Cleaning should be done only after the device has cooled down completely.
2. Once the device is cool.
3. Grasp the Top tank (B) with a dry hand and do not press or pull on the handle.
4. Grasp the Bottom tank (C ) with your other hand.
5. Twist the Top tank (B) counterclockwise until you unscrew the Top tank (B) from the Bottom tank (C ) making sure not to press or pull
on the handle.
6. Once you open the device take out the Disk Filter (J) and the Funnel filter (I).
7. Empty the Funnel filter (I) and clean it with water and a paper towel removing the used coffee ground.
8. Clean the Disk Filter (J) with water and a paper towel.
9. Empty the remaining water from the Bottom tank (C ) and clean the inside of the tank with a soft towel, washing up liquid and water,
and then dry with a paper towel.
10. Clean the Upper disk (L) and the Gasket (K) with a paper towel.
11. Clean the Top tank (B) with water, washing up liquid, and a paper towel.
12. Leave the device to dry and then assemble it back before storage.
Changing the Upper disk and Gasket:
After some time the Gasket (L) and upper disk (K) will deteriorate. The gasket will start to fall apart and the filter will discolor or lose its
shape. TO exchange,
To exchange the Disk and Gasket:
1. Check if the device hot from previous use. Exchange should be done only after the device has cooled down completely.
2. Once the device is cool.
3. Grasp the Top tank (B) with a dry hand and do not press or pull on the handle.
4. Grasp the Bottom tank (C ) with your other hand.
5. Twist the Top tank (B) counterclockwise until you unscrew the Top tank (B) from the Bottom tank (C ) making sure not to press or pull
on the handle.
6. On the bottom side of the Top tank (B) you will see a round rubber gasket and a metal filter.
7. Using a thin blade lift the gasket downwards releasing it from its place along with the upper disk.
8. Dispose of the old gasket and upper disk.
9. To install put the metal disk in the middle of the empty space with the bulge of the filter facing you.
10. Push the new gasket around the filter and then using your finger move the gasket around the new filter until it falls into place.
11. You can screw the Top tank back on to see if the gasket is in place.
WARNING: Please note that both the Rubber gasket (K) and the Upper disk (L) are consumable parts and are not covered by the device
warranty. Ask your local seller for the availability of the spare disk and gasket. (CR 4415.1 disk and gasket set.)
TIP: After changing the gasket the rubber might change the taste of the coffee depending on the coffee acidity it is advised to make a few
cups of either just water or used coffee grounds to remove the taste off the rubber.
Troubleshooting:
Problem:
No coffee in Top Tank (b)
Cause:
No water in the Bottom tank (C).
Solution:
Add water to the Bottom tank (C)
Problem:
Coffee making takes a long time.
Cause:
Bad coffee type. Too coarse or too fine.
The filter is blocked.
Solution:
Use special coffee for Mocca.
Clean the top filter.
Problem:
5

Publicidad

loading