Possible Problems And Solutions - Oursson TP3310PD Manual De Instrucciones

UTILIZATION, Рiс. С
Control panel, Рiс. С-1
BOILING button
1.
2. TIMER button
3. TEMPERATURE button
4. POUR button
5. UNLOCK button
6. Unlock indicator
7. Display
Display, Рiс. С-2
1. Water temperature indication
2. Timer
3. Temperature selection indication
4. Unlock indication flashes when unlocked
5. Lock indication
6. Timer indication flashes when sets
7. Boiling/re-boiling indication flashes when one of the
functions is on
8. BOILING indication
9. WARM UP indication
Thermo pot is design only for heating clean drinking
water.
You can use thermo pot in the following modes:
• Heating water to a predetermined temperature;
• Maintain selected water temperature;
• Boil water.
The device is equipped with protection from
switch-on without water. If you turn on the
device with no water or less then MIN mark, the
device will turn off after a few seconds. After the
heating element cools, the device will get back to
working condition, POSSIBLE PROBLEMS AND
SOLUTIONS section.
To accelerate the cooling of the heating
element, do not fill the device with cold water.
This may damage the heating element.
Before first use:
• Wash the inner surface of the device with the use of non-
abrasive cleaners. Dry the device. Wipe the device with a
clean dry cloth.
• Boil the maximum amount of water. Monitor for no leaks,
sparks, melting of body, excessive heating of the power
cord, plug, and burning smell during first two boiling.
• Boiled water from the first two boiling is not recommended
to use in food. Y ou can use it for everyday needs.
OPERATION ORDER
Filling with water, Рiс. С-3, С-4
1. Unlock the lid by pressing the button in the handle,
Pic. C-3
2. Drag the lid's handle up.
3. Fill the inner container with cold water till "FULL" mark,
using a kettle or other suitable kitchenware, Pic. C-4
4. Close the lid till you hear a click.
NOTE! If you fill the device with hot water, automatic
protection that turns off the heating element may turn on.
14
Never fill thermo pot directly from the tap, because
the water spray can get into the device or control
panel and cause a short circuit, electric shock or
malfunction of the device.
Boiling, Рiс. С-5
1. Plug in the device.
2. Boiling will start automatically, indication will light
up. Display will show the current water temperature.
Temperature will increase step by step.
3. After boiling, the device will go into a temperature
maintain mode 85 C, indication will be lit. When the
o
temperature will be lowering, automatic warm up turns
on.
First, insert the power cord into the device and only
then insert the plug into the outlet. Violation of this
order may result in electric shock.
Re-boiling
By adding cold water into the thermo pot when it is in
WARM UP mode, re-boiling mode will automatically start,
indication lights up.
NOTE! If you will add a small amount of water, re-boiling
function may not start automatically, indication will lit,
press to start boiling.
Beware the burst of steam when opening
the lid of the device.
Heating water to a predetermined temperature
1. Fill the device with water. Plug in the device. The display
will show the current temperature. Boiling will start
automatically, indication will light up.
2. Press button a few times to set the desired heating
temperature of the water. The minimum value of heating is
40° C, maximum - 98° C. Available values are: 40, 50, 65,
85 and 98° C.
3. While heating, you may change the temperature by
pressing button.
After the water is heated to a predetermined temperature,
the device will switch automatically into the WARM UP
mode, showing the current temperature.
NOTE! If you will unplug the device for a few minutes and
then plug it again, the device will switch into a WARM UP
85° C mode.
Water supply, Рiс. С-6
Make sure the button is unlocked, indicator is lit up
and indication flashes. Take a cup for drink and place
it under dispenser.
Method 1: press and hold
button. While you hold the
button, water is supplied through the dispenser. Release the
button to stop water supply. Pic. C-6-1.
Method 2: with cup press the knob behind the dispenser,
while you press the knob the water supplies through
dispenser. Release the knob to stop water supply.
Pic. C-6-2.
To determine the level of remaining water in the
device, use the scale.
Automatic lock, Рiс. С-7
The device is equipped with automatic lock from water
supplying and pressing button, the display indication is
. The lock turns on automatically if there are no actions
within 10 sec. To unlock press button, indication will
flash and indication will be lit up.
Delayed start, Рiс. С-8
1. Press button a few times to set the timer, available
values: 3, 6, 12, 18, 24, 48, 72, 99 hours.

POSSIBLE PROBLEMS AND SOLUTIONS

Problem Solution
The device is unplugged.
Cord's contacts are dirty.
Water isn't boiling
Bad outlet contact
Water supply lock is on
Hot water pour badly immediately after boiling
Water pours badly from
the dispenser or does not
The device is unplugged.
pour at all
Bad outlet contact
Mineral scurf or impurities in the inner container
Water pours itself from
The maximum water level is exceeded.
the device
Rust stains, plaque on
the inner surface of the The surplus of iron, minerals in the used water
container
White particles float in The surplus of iron, minerals in the used water,
water which causes scurf
When boiling a loud The surplus of iron, minerals in the used water,
noise can be heard which causes scurf in the inner container
When using new device or after a long break, a
slight plastic smell may be felt.
Hot water has a bed
smell
Your water is heavily chlorinated: by boiling the
smell intensifies
When the surrounding temperature is high while
When using, the device boiling and maintaining the temperature at 85 or
becomes hot 98° C, the device's body can reach temperatures
higher than 65° C
LED-display and unlock
Automatic protection is triggered : water level is
indication are flashing
below minimum (see Automatic lock).
simultaneously.
cLeAning AnD mAinTenAnce, Рiс. D
Hard water can leave scale in the device. Use special
cleaners for descaling. Follow the instructions of the used
detergent. Do not use abrasive or harsh cleaners.
• Fill the device halfway with water.
• For every 2 cups of water, add 6 tablespoons of white
vinegar 8%.
• Bring to a boil.
• Repeat the procedure if necessary.
• Unplug it.
• Allow the device to cool.
2. Countdown will start automatically and display will show
remaining time before start.
3. After the countdown, the device will start boiling water.
4. To cancel the timer, press button a few times until
"00:00" is displayed.
Plug in the device
Clean the cord's contacts
Repair the outlet
Before pressing the button, unlock the
water supply by pressing button.
Wait a few minutes or carefully open the lid
for a few seconds for excess steam to exit.
Beware of the burst of steam!
Plug in the device
Repair the outlet
Clean the inner container (see. Cleaning
and maintenance).
Pour the excess water from the device.
Do the cleaning cycle using citric acid or
descaling detergent (see. Cleaning and
maintenance).
Boil and pour water for several times.
Use bottled water.
If the temperature of the body is near
65° C it is normal.
Add cold water and press button.
• Remove the lid, Pic. D-1
• Open the lid under 45
0
• Press the fixator behind and pull the lid as shown in the
picture.
• Remove the lid.
• Rinse the device twice with cold water, Pic. D-2.
Wipe the device's body with a damp cloth. In order
to prevent electrical shock do not immerse the
entire product or the wires into the water.
• Thoroughly dry all the parts of the device.
• Set the lid back, you will hear a click sound, Pic. D-3.
15