Dust Suction; Switching On/Off - EDM 08753 Manual De Instrucciones

Mouse Sander
Operating Instructions
Before use
Remove any packing material and loose parts from unit.
Check the accessories before use. It should be fit with the
machine and your purpose. If the machine is new, the battery
must first be charged.
Attention! After long time storage, the battery capacity will
be reduce.
A new battery or one which has not been used for an
extended period achieves full performance only after
charging and discharging cycles. A substantial drop in
operating period per charge indicates that the battery is
worn out and must be replaced.
Battery charger (fig.1)
The lithium-ion battery can be charged at any time and will
not develop a "memory" when charged after only a partial
discharge. It is not necessary to run down the battery pack
charge before recharging. Remove the battery pack from the
tool when convenient for you and your job. You can "top-off"
your battery pack's charge before starting a big job or long
period of use.
Due to lithium-ion's fade-free properties, the only time it is
necessary to charge the lithium-ion battery pack is when the
pack has reached the end of its charge. To signal the end of
charge, power to the tool will drop quickly. Charge the
battery pack as needed.
1. Charging the battery
This lithium-ion battery pack is shipped partially charged.
Before using it the first time, fully charge the battery pack. A
fully discharged battery pack with a temperature between
5°C and 40°Cwill charge in about 1 hour for 2.0Ah battery
pack.
.Plug the charger adapter into power source. The green light
on the charger stand will illuminate, indicating the charger is
powered.
.Slide the battery all the way into the charger stand. The
green light is off, and the red light on the charger stand will
illuminate, indicating that the battery is charging.
l The red light will go off after charging is complete and a
green light will appear.
NOTE: Batteries may become warm while charging. This is
normal. If the battery is hot after continuous use in the tool,
allow it to cool down to room temperature before charging.
This will extend the life of your batteries.
WARNING: Always disconnect the battery pack from the tool
before any assembly, adjustments or changing accessories.
2. Insertion and removal of rechargeable battery (fig.2)
Depress the battery-release button located on the front of
the battery pack to release battery pack. Pull the battery
pack out and remove it from the tool.
Warning!
Always remove the battery pack before making adjustments
to the equipment.
Be sure to read the following information before you put the
cordless equipment into operation: Charge the battery pack
INSTRUCTION MANUAL
EN
with the charger. An empty battery pack requires a charging
period of approximately 0.5 to 1 hour for 2.0Ah battery pack.
Fitting the dust bag (fig.3)
Fit the dust bag out and remove it from the tool.
Caution!
For health reasons it is imperative that you use
the dust collection box or a dust extraction system.
For others material, always work with the dust extraction
device!
Fit and remove the sanding sheet (fig.4)
Perforated sanding sheets are used for dust suction. Please
always make sure the sheet corresponds with perforation in
sanding foot.
Always use the tool with the total sanding surface covered
with sanding paper.
Change the sanding sheet regularly. Do not continue to use
worn, torn or heavily clogged sanding sheets.
The self-adhesive sheet can be stuck on sanding surface
directly. And can be peeled away from the base simply.

Dust suction

Empty dust bag regularly for optimal dust pick-up
performance.
When sanding metal, sparks are
generated; do not use dust bag and
keep other persons and combustible
material from work area.

Switching On/Off

To turn on the equipment, move the switch from position "0"
to position "1" To turn off the equipment, move the switch
from position "1" to position "0"
Working with the eccentric grinder/sander
• Place the whole surface area of the sanding disk on the
material.
• Switch on the machine and move it with gentle pressure
over the workpiece, making circular or
Transverse and linear movements
• Use a coarse grit for coarse sanding and a finer grit for finish
sanding. You can find the best grit size for the job by carrying
out sanding tests.
Caution! The dusts which are formed while the equipment is
being used may be a health hazard:
• Always wear safety goggles and a dust mask during sanding
work.
REF. 08753