Emos H3019 Manual De Instrucciones página 6

4. If you wish to erase all unlock codes, enter 99 instead of
the 3-digit location (cell) code and press # to erase all
unlock codes.
5. You can also gradually erase codes after hearing the con-
firmation sound (a single long beep) by pressing #. Doing
so will automatically select the code for the next location
(cell) for deletion.
6. Press * twice to exit the deletion mode. You will hear a
short double beep.
Setting an RFID code:
1. Input the code for entering the programming MENU (either
123456 or the code you chose). You will hear a double
long beep.
2. Press 3 and # to enter the password setting MENU. You will
hear a single long beep.
3. Enter a 3-digit location (cell) code from 000 to 199 and press
#. You will hear a long beep.
4. Use an RFID chip on the IC reader. You will hear a single
long beep, indicating the chip was successfully saved. If the
given chip is already in the door unit's memory, you will hear
a short double beep.
5. You can use chips on the IC reader one after another and they
will automatically be saved into consecutive locations (cells).
6. Press * twice to exit the programming MENU. You will hear
a short double beep.
Deleting an RFID code:
1. Input the code for entering the programming MENU (either
123456 or the code you chose). You will hear a double
long beep.
2. Press 4 and # to enter the code deletion mode. You will hear
a single long beep.
3. Enter the 3-digit location (cell) code (from 000 to 199) of the
cell you wish to delete the code for and press # to erase the
code for this location (cell). You will hear a single long beep.
4. If you wish to erase all unlock codes, enter 99 instead of
the 3-digit location (cell) code and press # to erase all
unlock codes.
5. You can also gradually erase codes after hearing the con-
firmation sound (a single long beep) by pressing #. Doing
so will automatically select the code for the next location
(cell) for deletion.
6. Press * twice to exit the deletion mode. You will hear a
short double beep.
Setting keypad illumination:
1. Input the code for entering the programming MENU (either
123456 or the code you chose). You will hear a double
long beep.
2. Press 7 and # to enter the keypad programming MENU. You
will hear a single long beep.
3. Enter:
a. 00 – keypad illumination off
b. 01 – keypad illumination always on
c. 02 – keypad illumination on only when the keypad is in
use, otherwise off
4. Press # to confirm. You will hear a single long beep.
5. Press * once to exit the keypad programming MENU. You
will hear a short beep.
Installation
Installing the Door Camera Unit
(See Fig. 2)
Choose a suitable mounting spot and install the mounting frame.
Pull the connection cable through the mounting opening and
connect it to the door camera unit's wiring. Mount the connected
door camera unit onto the mounting frame using the enclosed
screws.
Door Camera Unit on Plaster
Apply a layer of silicone between the wall and the door camera
unit to prevent ingress of humidity under the door camera unit.
The silicone should be applied on the top and the sides. The bottom
side must be left open to allow humid air from exiting the space
under the door camera unit.
Parameters of Connection Cables
For distances under 20 m, use a high-quality shielded FTP CAT.5
cable (optimally CAT.6). For distances over 20 m, we recommend
a SYKFY 5 × 2 × 0.5 or 10 × 2 × 0.5 cable. To achieve a higher
cross-section, the cables can be doubled or tripled.
The resulting diameter of the conductors is as shown in the table:
Conductor core diameter (mm)
0.5
0.65
6
Distance (m)
20
50