Publicidad
Idiomas disponibles
Idiomas disponibles
GENERAL INFORMATION
PACKAGING AND RETURNS Experienced packaging personnel at LaMotte Company assure
adequate protection against normal hazards encountered in transportation of shipments. After
the product leaves the manufacturer, all responsibility for its safe delivery is assured by the
transportation company. Damage claims must be filed immediately with the transportation
company to receive compensation for damaged goods. Should it be necessary to return the
instrument, pack the instrument carefully in a suitable container with adequate packing material.
A return authorization number must be obtained from LaMotte Company by calling 1-800-344-
3100 or 1-410-778-3100, ext. 3 or emailing softwaresupport@lamotte.com. Attach a letter with
the authorization number to the shipping carton which describes the kind of trouble experienced.
GENERAL PRECAUTIONS Read the instruction manual before attempting to set up or use the
instrument. Failure to do so could result in personal injury or damage to the meter. The WaterLink
Spin Touch should not be stored or used in a damp or excessively corrosive environment. Care
should be taken to prevent water or reagents from entering the photometer chamber. Wet disks
should never be put into the photometer chamber.
SAFETY PRECAUTIONS Read the safety precautions on the labels of all reagent containers and
packaging prior to use. Safety Data Sheets (SDS) can be found at www.lamotte.com. Additional
emergency information for all LaMotte reagents is available 24 hours a day from the National
Poison Control Center at 1-800-222-1222 or by contacting the 24 hour emergency line for
ChemTel at 1-800-255-3924 (USA, Canada, Puerto Rico). For locations outside of the North
American continent call 813-248-0585 collect.
Ensure that the protection provided by this equipment is not impaired. Do not install or use this
equipment in a manner that is not indicated in this manual.
LIMITS OF LIABILITY Under no circumstances shall LaMotte Company be liable for loss of life,
property, profits, or other damages incurred through the use or misuse of its products.
CE MARK The WaterLink Spin Touch meter has been independently tested and has earned
the European CE Mark of compliance for electromagnetic compatibility and safety. To view
certificates, go to the LaMotte website at www.lamotte.com.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a residential
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
¬ Reorient or relocate the receiving antenna.
¬ Increase the separation between the equipment and receiver.
¬ Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
¬ Consult the dealer or an experienced radio/TV technician for help.
NSF CERTIFICATION The NSF/ANSI/CAN 50 certification mark on a water quality testing
device (WQTD) used in recreational waters, such as pools and spas, means that the
product was reviewed and certified by NSF International to meet applicable American
National Standards for product design and performance. NSF tests and re-tests
products to confirm that they comply with all requirements of certification for performance,
accuracy and operating range. Certification levels of L1, L2, and L3 are possible with L1 being the
highest rating. Go to
For the most recent WaterLink Connect 2 update and the most recent Spin Touch firmware
update, customers who intend to use a WaterLink Spin Touch Meter for NSF certification
compliance purposes should:
1. Visit
softwarecenter.lamotte.com
Windows.
www.nsf.org
for more information.
and download the WaterLink Connect 2 application for
15
Publicidad
