Publicidad
Idiomas disponibles
Idiomas disponibles
continue with the next programming or exit
programming.
Programming room numbers related
to the addresses activated by pressing
button 2 (codes 019 and 021).
If the short or long pressure, or both, are
assigned the same address with which the
videointercom is called from outside, the
service that is activated is the intercom call
within the same flat. In order to correctly
address this call, the room number associ-
ated to the short/long pressure of button 2
must be programmed with the room num-
ber corresponding to the intercom/video-
intercom to be called. Allowed values are:
- address 000-007: room numbers;
- address 255: delete previously entered value.
Programming the room number related
to the address associated with short
pressure of button 2 (code 019).
To program the room number related to the
address associated with short pressure on
button 2 (by default empty), it is necessary:
enter code 019;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming the room number related
to the address associated with long pres-
sure of button 2 (code 021).
To program the room number related to the
address associated with long pressure on
button 2 (by default empty), it is necessary:
enter code 021;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming the address of the service
activated by closing contact A1/GN (code
022).
When the input terminals A1 and GN of the vide-
ointercom are closed by means of a button, the
floor call is forwarded (the videointercom rings
with the melody programmed for this type of
call, without enabling the conversation). It is
possible to associate an address to the input
if, in addition to receiving the floor call tone,
one of the services below is to be activated:
- address 000: floor call forwarded to all
apartment stations having the same user
address of the videointercom where A1 and
GN are closed together;
- addresses 001-200: floor call sent to another
user;
- address 255: delete previously entered value.
To program the address associated with clos-
ing contacts A1/GN (by default empty), it is
necessary to:
enter code 022;
press button
; o confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming of the room number related
to the address of the service activated
by the closing of the A1/GN contact (code
023).
If the input A1/GN is assigned as address the
same address with which the videointercom
is called from outside, the room number of the
apartment station to which the floor call will
be sent must be set. Allowed values are:
- address 000-007: room numbers;
- address 255: delete previously entered value.
To program the room number relative to the
address of the service activated by the closing
of the A1/GN contact (by default empty) it is
necessary:
enter code 023;
press button
to confirm;
enter the new address; enter 255 to erase a
value previously entered;
press button
to confirm;
continue with the next programming or exit
programming.
Programming ringtones (codes 024 to
032).
The following parameters can be programmed
in relation to the ringtones. First input the
code (024-032) and then the value to be set:
-code 024: code identifying the common vol-
ume level associated with all the ringtones
(factory value 3, allowed values from 1=min-
imum to 5=maximum);
-codes 025, 026, 027 and 028: the four codes
identifying the ringtone set for calls from the
external door station, from intercom within
the same flat, from another flat and from the
floor respectively (see table 1 for the factory
settings;)
- codes 029, 030, 031 and 032: the four codes
identify the number of rings associated to the
ringtone set for calls from external door staion,
intercom inside the same flat, from another
flat and from floor respectively (for factory
settings see table 1, allowed values from 1 to 5).
To perform the desired programming it is
necessary:
enter one of the codes from 024 to 032;
press button
to confirm;
enter the new value to be assigned;
press button
to confirm;
continue with the next programming or exit
programming.
Programming video always ON even in
slave monitor (code 033)
It is possible to configure the SLAVE videoint-
ercom so that its display will switch on when
the call is received (by default it is switched
off). It is necessary:
enter code 033;
press button
to confirm;
enter the value 222 to enable switching on
or the value 212 to disable it;
press button
to confirm;
continue with the next programming or exit
programming.
Attention. To provide correct system
dimensioning, contact the Farfisa
technical service before enabling the
option.
Return to factory defaults
To return to the factory settings, it is neces-
sary to:
enter programming mode following the
instructions described in the paragraph
"Entering programming mode",
press the following buttons in this se-
quence:
, 2 ,1 and
;
the
icon LED stops flashing, the
LED lights up for one second and then the
icon LED returns to flashing slowly;
exit programming. If new programming is
required, re-enter and perform the neces-
sary steps.
Attention: returning to the factory
defaults has no effect on the user address,
which is set manually via the dip-switches
of SW1.
Mi 2577
icon
- 11 -
Publicidad
