SUHNER ABRASIVE ROTAR Documentación Técnica página 25

tion bore. Make shure that the locking knob snaps in.
2.1.3 h
And tool
Slide hand tool over the hose coupling. Make sure that the
locking knob snaps in. For more information please refer
to the user's manual of the hand tool.
2.1.4 A
brAsive
For detailed information please refer to the user's
technical document for the hand tool used.
The abrasive must be fastened snug against in-
stalled tools.
Let the abrasive run briefly at idling speed without load.
In the event of strong vibrations or other deficiencies shut
down the machine immediately and rectify deficiencies or
fit a new abrasive.
2.1.5 s
Afety guArd
If a safety guard is supplied with the hand tool, it is
imperative that the safety guard be used.
2.2 r
Ating dAtA
2.2.1 s
pecificAtions
3-phase AC motor:
Power voltage
Power Input
Power Output
Protection class
Type of protection
No-load speed
50Hz: 1000/1700/2700/5100/7300/13500min
60Hz: 1200/2000/3200/6100/8700/17000min
Sound pressure level
Flexible shafts with connection thread DIN15:
DIN15, NA10, NA12, NA15
42V/400V, 50Hz
230V/460V, 60Hz
Type 3.8: 3800W, 60Hz
Type 2.8: 2800W, 60Hz
Type 3.2: 3200W, 50Hz
Type 2.4: 2400W, 50Hz
Type 3.8: 3200W, 60Hz
Type 2.8: 2300W, 60Hz
Type 3.2: 2700W, 50Hz
Type 2.4: 2100W, 50Hz
1
IP44
-1
-1
2
50Hz: 77dB(A), K=1.5m/s
2
60Hz: 80dB(A), K=1.5m/s
M14 see catalog
2.2.2 v
ibrAtion mesurement vAlues of hAnd tools
FH15
Measurement value <2.5m/s
WH15
Measurement value <2.5m/s
SAM 1:1
Measurement value <2.5m/s
TAM 1:1
Measurement value <2.5m/s
According to ISO/DIS 8662.4
The specified vibration value was measured with a
standardised test method and may differ from the
actual operating value. The specified value can be
used for product comparisons or for an introductory as-
sessment of work breaks.
2.3 o
perAting conditions
Temperature range during operation: 0 to +50°C
Relative air humidity: 90% at +30°C, 65% at +50°C
To avoid strong looping movements and beaming
of the flexible shafts, the working pressure must
be reduced.
3.
haNDLINg
3.1 m
Achine
3.1.1 s
elect the speed
Pull the locking pin to disengage it. Set the speed you
want by pulling or twisting the eccentric.
You may set the speed only when the tool is
switched off.
3.1.2 s
tArting the mAchine
Before turning on the machine, make sure to re-
move wrenches and adjusting tools.
When turning on, hold the flexible shaft extended.
During operation make sure that the flexible shafts have
Test grinding wheel ø 100x25
2
/K=1.5m/s
Drive 8700min
Test grinding wheel ø 100x25
2
/K=1.5m/s
Drive 5100min
Test grinding wheel ø 230x6
2
/K=1.5m/s
Drive 6100min
Test grinding wheel ø 100x25
2
/K=1.5m/s
Drive 6100min
/ o
PERaTIoN
25
2
-1
2
-1
2
-1
2
-1