Gemini MM-02 Manual Del Operador página 4

INTRODUCTION
Congratulations on purchasing a Gemini MM-02 4U 19",
4 channel, rack mounted club mixer. This state of the
art mixer is backed by a three year warranty, excluding
crossfader and channel slides. The crossfader and chan-
nel slides are backed by a separate 90 day warranty. Prior
to use we suggest that you carefully read all the instruc-
tions.
FEATURES
- 4U 19" Rack Mounted Club Mixer
- 4 Stereo Channels
- 7 Line, 2 Mic, 2 Convertible Phono/Line, RCA Inputs
- 3 band Rotary Master EQ Control with Cut Feature
- Master, Zone and Record RCA Outputs
- Fully Removable, User Replaceable Rail Glide Cross Fader
- Push Button Mono Control
- Rotary Gain Control Per Channel
- XLR Mic Input with 2 band Rotary Control EQ Volume
- Dual Display with Bright LED
- Auto Talk-Over Feature
- Push-Button Cueing with Cue/PGM Fader Control
- Balanced Master Output
- Top Located 1/4" Headphone Input
CAUTIONS:
1. All operating instructions should be read before using
this equipment.
2. To reduce the risk of electrical shock, do not open the
unit. Please refer servicing to a qualified service technician.
In the USA ~ if you experience problems
with this unit call Gemini Customer Service at: 1
(732) 738-9003. Do not attempt to return this equip-
ment to your dealer.
3. Do not expose this unit to direct sunlight or to a heat
source such as a radiator or stove.
4. This unit should be cleaned only with a damp cloth.
Avoid solvents or other cleaning detergents.
5. When moving this equipment, it should be placed in its
original carton and packaging. This will reduce the risk of
damage during transit.
6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOIS-
TURE.
7. DO NOT USE ANY SPRAY CLEANER OR LUBRI-
CANT ON ANY CONTROLS OR SWITCHES.
CONNECTIONS:
1. Before plugging the power cord in, make sure that the
VOLTAGE SELECTOR (2) switch is set to the correct
voltage (115 or 230).
2. Located on the rear panel is the 115/230V PLUG (1)
used to plug in the power cord. Before plugging the power
cord in to the 115/230V PLUG (1) and then into an elec-
trical output, make sure the POWER SWITCH (50) locat-
ed on the face panel is turned OFF.
3. The MM-02 has 4 sets of outputs:
- The BALANCED MASTER (6) ouput jacks connect the
mixer to main amplifier using standard cables with 1/4"
connectors. We recommend using balanced cables if the
distance to your amp is 10 feet or more.
- The MASTER (3) output jacks also connect to the main
amplifier with RCA cables.
- The ZONE (5) output jacks allow the connection of an
additional amplifier with RCA cables.
- The REC (4) output jacks can be used to connect the
mixer to the record input of your recording unit, thus
enabling you to record your mix with RCA cables.
4. Located on the rear panel are 2 Phono(PH)/Line(LN)
convertible RCA inputs (11, 14), and 5 line RCA inputs
(7, 8, 10, 15, 17). The convertible RCA inputs (11, 14)
for Channel (CH) 2 (40) & 3 (44) allow PH and LN level
equipment to be connected to the mixer. To adjust the
converter(s) (9, 13), just flip the switch UP to operate
PH1 or PH 2. Flip the switch DOWN to operate through
LN 2 or LN 4. The PH INPUTS only accept turntables with
a magnetic cartridge. When using (a) turntable(s), you will
need to ground the RCA cable(s) by screwing in the
grounding fork(s) to the GROUNDING SCREW (12)
located in the back panel of the MM-02 mixer. This is
located in between the CONVERTER SWITCHES (9, 13).
The stereo LN INPUTS only accept line level inputs such
as a CD, DAT, MiniDisc, etc.
NOTE: NOT ATTACHING A GROUND MAY CAUSE A SYSTEM "HUM."
5. Headphones may be plugged into the face-plate located
1/4" HEADPHONE JACK (18).
6. The MIC 1 (28) input (located on the front panel) accepts
an XLR connector. The MIC 2 (16) input (on the rear
panel) accepts 1/4" connectors. Both accept balanced
and unbalanced microphones.
OPERATION:
1. Once all of your connections have been in the rear
panel, turn on the mixer by pressing the POWER
SWITCH (50).
2. CHANNEL 1: To bring this channel in to program output
(PGM), you must first decide which line will be in use. Use
the LN SWITCH (33) to toggle from LN 1(17) to Mic 2
(16) on this channel. Slowly raise the CH1 SLIDE CON-
TROL (36) to a comfortable level, once you've selected
the proper line. You can further modify the sound output
of this channel by adjusting the rotary GAIN (34) control
located below the LN SWITCH (33).
3. CHANNEL 2: To bring this channel in to PGM, you must
first decide which line will be in use. Use the LN SWITCH
(37) to toggle from PH1/LN 2 (14) to LN 3 (15) on this
channel. Slowly raise the CH 2 SLIDE CONTROL (40) to
a comfortable level, once you've selected the proper line.
You can further modify the sound output of this channel
by adjusting the rotary GAIN (38) control located below
the LN SWITCH (37).
4. CHANNEL 3: To bring this channel in to PGM, you must
first decide which line will be in use. Use the LN SWITCH
(41) to toggle from PH2/LN 4 (11) to LN 5 (10) on this
channel. Slowly raise the CH 3 SLIDE CONTOL (44) to a
comfortable level, once you've selected the proper line.
You can further modify the sound output of this channel
by adjusting the rotary GAIN (42) control located below
the LN SWITCH (41).
5. CHANNEL 4: To bring this channel in to PGM, you must
first decide which line will be in use. Use the LN SWITCH
(45) to toggle from LN 6 (8) to LN 7 (7) on this channel.
Slowly raise the CH 4 SLIDE (48) control to a
(4 4 )