Descargar Imprimir esta página

VONROC LM507 Serie Traducción Del Manual Original página 8

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 21
EN
To readjust the blade mechanism:
1. First check the counterblade (12) and mower
blade (11) for notches/dents. It might be
necessary to remove these with a grindstone.
2. To reduce the distance between the
counterblade (12) and the mower blade (11),
turn the counterblade adjustment nut (10)
clockwise. Turn the counterblade adjustment
nut (10) counterclockwise to increase the
distance.
3. Adjust both counterblade adjustment nuts (10)
until the mower blade (11) lightly brushes the
entire length of the counterblade (12).
4. Insert a piece of paper (e.g. A4 paper) between
the counterblade (12) and the mower blade (11).
5. Now lightly tighten both counterblade
adjustment nuts (10) clockwise a little at a time
until the mower blade (11) cuts the paper
evenly across the whole blade length.
Note: the blade (11) and counter-blade (12) act like
a pair of shears.
Proper use (Fig. H)
• For best results, place the lawnmower on
the edge of the lawn and mow in the forward
direction. Then turn at the end of each run
and mow in the opposite direction, slightly
overlapping the previously cut strip. Also refer
to figure H.
• Make sure that the lawn is clear of stones,
sticks, wire or other objects that could damage
the product or its product.
• Do not cut wet grass because it tends to stick
to the underbody of the product, preventing the
proper discharge of grass clippings, and it could
also cause you to slip and fall.
• Never cut off more than one-third of the total
length of the grass for a healthy lawn. In the
autumn, lawns should only be cut as long as
there is growth.
• Circle around flower beds. When reaching
a flower bed in the middle of the lawn, cut a row
or two around the circumference of the bed.
• Pay special attention when changing direction.
• Always mow along inclines (not up and down).
You can prevent the lawn mower from slipping
down by holding a position at an angle up-
wards.
• Select the cutting height according to the
length of the grass. Make several passes to
prevent that too much grass is cut at one time.
8
• Empty the grass box regularly.
Storage (Fig. I, J)
Store the machine in a secure, dry place out of the
reach of children. Do not place other objects on top
of the machine.
• To store the lawn mower, fold the handle
forwards as shown on figure I.
• A wall bracket (8) is included with the delivery
to mount the folded lawn mower onto a wall
when preferred. Use the provided screws to
mount the wall bracket. Use appropriate wall
plugs if necessary.
5. MAINTENANCE
Your mower has been designed to operate
over a long period of time with minimum of
maintenance. Continuous satisfactory operation
depends upon proper mower care and regular
cleaning.
• Keep the mower clean and dry.
• Regularly use a blunt scraper to remove grass and
dirt from the mower
• To clean the mower, use only mild soap and
a damp cloth. Never let any liquid get inside the
tool and never immerse any part of the tool into
liquid. Do not use any abrasive or solvent - based
cleaner.
Stop the blade(s) if the machine has to be tilted for
transportation when crossing surfaces other than
grass, and when transporting the machine to and from
the area to be used.
Replace worn or damaged parts for safety. Use only
genuine replacement parts and accessories.
WARRANTY
VONROC products are developed to the highest
quality standards and are guaranteed free of defects
in both materials and workmanship for the period
lawfully stipulated starting from the date of original
purchase. Should the product develop any failure
during this period due to defective material and/or
workmanship then contact VONROC directly.
The following circumstances are excluded from this
guarantee:
WWW.VONROC.COM

Publicidad

loading

Este manual también es adecuado para:

Lm508 serie